If you are in the US the local dealer will give you a PDF version for free. They will want the casting serial number (not the serial number on the electrical cabinet).
CNC Machine Tool Sales, CNC...
Type: Posts; User: old timer okuma
If you are in the US the local dealer will give you a PDF version for free. They will want the casting serial number (not the serial number on the electrical cabinet).
CNC Machine Tool Sales, CNC...
As long a the DC bus stays above 240 DC from VH to VL you should be fine. It needs to be 300 DC (assuming 220 incoming), but if you incoming is at least 196 AC you should be fine. The ohm reading...
I was pretty sure at least one of the manuals that came with the machine had the parameters. On newer controls the operations manual has them in the back. The 3000 may have operators book. If not...
The door interlock needs 24 volts to unlock the door. If you have power to the switch from the machine outputs and the door still won't unlock then the switch may be bad. There machines usually...
The code #13 points to a overcurrent alarm. Megger test the motor and if over 200 meg at 500 volts and the alarm can't be reset. If it can't then replace the drive unit.
that parameter page should have a parameter to ignor the bf alarm when machine is not in linked mode and another to ignore the spindle interlock when bf is not in linked mode.
This is the spindle interlock signal for the barfeeder. This is an input from the barfeeder to the machine. You can also ignor the alarm by setting a parameter on the barfeeder user parameter page...
what model? unless you have a special model table/interface you should be able to disconnect the cables at the top of the inside of the cutting area, not at the table. most okuma controls look for...
Rotary table on what? If it is a 4th axis on a vertical machine then unplug it with power off at the bulkhead. If it is on a horizontal then it is part of the machine and most likely no.
be careful restricting the air. This is the only way to evacuate the oil-air waste oil lubricating the bearings. If the bearings get too "wet" you will over heat them and could damage the bearings.
"LDU" stands for linear drive unit. The older okuma machines with 3000 and 5000 (green screen machines) used LDU600 axis drives. The LDU name lingered even after the replacement with the early BDU...
This plane test happens before the software loads on the okuma. This is communication between the CRP board and the CRT unit itself. Check the cables to make sure all is tight and dry. Then swap...
look in the special functions manual for the machine. It covers the it in the 'periodic maintenance function'.
what LED's are on the drive when it stops and after rebooting? could be the drive, but could be the SVP board.
Is anyone righting Thinc apps yet? I am trying to learn and was wondering if anyone has an samples yet. I have seen the Thincster.com site and some of their examples.
If you know the motor is demaged and has happend more than once you need to consider the drive unit. If the machine has a BLII-D drive the cards connecting the base and the top board can get "loose"...
if you know the serial number the local okuma dealer can usually get the original values from Okuma.
sounds like all three coils are good. There is no way to check the rotor (that I know of). do you have AC voltage going to the resolver? and feedback when voltage when you spin the motor? The...
you can ohm out each of the 3 coils in the resolver. They shouldn't be open or short. next best would be putting a meter on them and look for an AC signal when rotating the motor.
You need to get a 'battery connection floppy' from your local dealer. This disk resets the battery date timer.
If you have the CPU led on then this could be a bad BDU drive. That would cause the 609 alarm.
Check the reset button. If you hold it in on a good machine it will make just the program lines flash.
if all the leds are off on the top board then the drive unit is dead. The 609 alarm is a generic alarm looking for the alarm signal from the drive back through the I/O system. So if the Magazine...
Is the drive hot? has the heatsink on the bad of the drive been cleaned? What alarm are you getting?
The FC encoder is smaller and more accuate than the other older style encoders. You may be able to use the FB to test, but the cover of the motor won't fit if the motor was built for the FB type.
How much tape storage does the machine have? How much free space does the machine say it has? Is this a new problem loading this size file?
The 7000 control you will want to get a D disk from the local dealer to make a complete parameter backup. The software itself you will not be able to backup.
There is a special disk for replacing...
The MSM is a safety speed unit. Okuma uses it to meet the CE spec in Europe. It is itegrated into the Okuma software and not possible to remove. The alarms on the unit should match up pretty close...
if you are talking about a little connector on the SRAM board itself, then that is for putting a battery to the board. Lets you take the SRAM off without it losing the charge from the battery on the...
are you sure you need both?