Search:

I had to replace the same parts in our VF4, low hour machine.
spindle load would fluctuate for no reason even when not in a cut.
Also had an awful noise that came and went, sounded like bearings....

No PM in my box
I still can't attach to a post here
If you post your email
I will send you the information you need

poly is forsure the stuff
ours lasts months running 8 - 10 hrs /day

Good morning Stinkfist
Send me a PM
For some reason my file will not attach to this post.
Chris J.

I will post them tomorrow, we run 1 of those at our shop,
It is a very productive machine.
Chris J.

Good point khaot183
Also
Are you programing G96 or G97?
What is the diameter being cut?

G50 S650 will limit the RPM to a max of 650 RPM so no mater what you program your G96 as the machine will only go to 650
You need to raise the G50 limit to whatever is safe for your setup
Best...

You can make your own
Is your machine to be anchored down or just sitting on the floor?
We used some 4" 4140 bar that was surplus
I just measured the height of them 5"
Any mild steel (44W or A36)...

Is your floor level?
Do you have the factory blocks for below the lift screws?
If both answers are yes then you will need taller blocks.
One of our machines requires 4.5" blocks to allow for...

I know you say tap heads do not excite you.
However you can tap very easily on a machine with an OT-C control
but you will need a floating tap holder, not much expense for a lot of work.
If you...

did you try this web site
????????????

I run in to this often with dxf files for our waterjet.
lines must be in the same plane
lines must be continous
you can't have any blocks
hope this helps

The savings will be great but will it be to code?
What about your insurance?

Good one pondo, that was my laugh for the day.
Not the comment about the VF-9 but the part about your wife.

Who are your dealers in Edmonton Alberta?

We run a BurrBench, it looks much the same as the PV series
It is very quiet, I have been around the Mr Debur they are quite loud.
We finish steel and aluminum in ours works well with both, we use...

Toymaker how many hours on your machine?

Has anyone taken the spindle motor off of a VF4 equipped with a 2 speed box.
ours sounds like it needs bearings.

I don't know if you are aware of it but I will throw this out there.
The geometry for an o-ring groove is not as straight forward as it may seem.
The side walls should taper between 2 to 5...

On a lathe or mill?

You will want to consider what size parts are to be machined,
as well as the length of your longest tool to be used.
To ensure there will be no clearance problems with the umbrella style

I found my paper work on the cable that Fanuc specified for us in 2003
The connections are as stated above by dccoupar.
Fanuc also says that on the 9 pin connection end to
jumper 7-8
jumper...

I would use caution on this one.
We did this several years ago with the same vintage controler, we used a cable from one of our other machines. (Different make same controler)
We got a 101 alarm...

Would you be able to supply the dxf file for your work?

We ran into the same problem quite often, and no amount of clamps would help on the table.
Recently I changed suppliers of our thin plate (1/16" - 5/8")
this has solved the problem for thin...

Do you have a tailstock or a B axis with tool turret

Have you tried Ash gear in Novi Mi.
There Ph# is 248-374-6155

My Miyano with an OT-C control uses
M17 to open
M18 to close
My Johnford with same control uses
M10 to close
M11 to open

Good luck
Chris J.

This would probably be a good part for the lost wax method.
(investment casting)
They can get great detail and cost is very low.
You also don't neet large #s far a run.

Try these guys
They have done some custom cutters for me, price and delivery is usually good
TJ Grinding
Waukesha WI.
262-549-6885