Search:

If it doesnt show anything on the screen and doesnt show any red leds on the motherboard, even if the red led of the power supply is lit, it is likely a problem with the power supply. If the red leds...

I do have the Fanuc 18T manual (all of them Programming, Connection, Maintenance). PM if you still need it.

Im not sure about the Hitachi J series but on some VFDs you can Coast to stop, which will 0 the voltage output and the drive will not try to stop the motor, which will effectivly end your alarm...

I got over error 1, it runs a little more of tape but this time it is showing error 2...¿Any ideas anyone?

Thats really not a good idea, one slip on the keypad while setting up and.. you have just indexed your turret into god knows what

-Jacob[/QUOTE]

Well I admit I tend to oversimplify things and...

OoooHH! Thats why it is interlocked on the PMC, you have a parts catcher that might get in the way of the tool change. As Jvangelder says you can do the PMC programming on the machine but you have to...

My email address is [email protected]

Yes! It is simple as that, you can add a keep relay, for example K90.0 and bypass the requierement for the tool change to be on a fixed position.
Do you have the tools to do this? You will need the...

ThePainter> I followed the procedure and everything that was supposed to happen happened, however instead of "Completed" in the screen it shows "Load Error 1".

Do you have any idea about what I am...

EX570 is a PLC alarm, you need to see on the ladder diagram what is causing it. You can do this by pressing the PARAM key several times until it shows you the ladder. Then look for the bit that is...

Those are to show time information in the display, im not sure if they will work, but it is worth a try....

Las máquinas con las que yo trabajo en mi día a día son máquinas para procesar metal, y sus husillos son enfriados por aceite y de una mucho mayor capacidad que el que utilizarías en un router para...

I think you also need to set a parameter, i do not remeber which one, i think is 0060.2, or 0014.2

Check the manual if you have one,

Good luck!

If I recall correctly some 900 parameters that open some options require the actual hardware to be connected. That may be why some of them won't work on your machine.

No he visto nunca ninguna unidad de esas instalada, pero por lo que dicen en la sección gringa del foro jalan muy bien. He instalado productos equivalentes de otras marcas y funcionan muy bien para...

Lo que yo quería que vieras es la manera en la que está acoplado. Si lo vas a usar para madera y acrílico entonces uno de esos motores chinos enfriados por agua bastan y sobran.
Los husillos, como...

El que ves en la foto es un motor para husillo chino enfriado por agua, se usan en los routers para cortar madera y materiales suaves, también se usan para cortar materiales muy duros como el granito...

I sold a controller to Radwell International (plccenter.com). They don't pay a lot but they are always buying and they pay for the freight.

El router Milwakee te puede servir para el husillo o cabezal como le dicen algunos. Las herramientas no serían las que usa un CNC standard, pero si el router usa broquero entonces puedes usar las...

MikieD:

Did you get this to work?

Pasa porque el Corel no genera el código necesario para hacer circulos. Probablemente requieras de un postprocesador, pero depende del control que estes utilizando.

Tal vez si convirtes el...

¿Tu la hiciste?? Te quedó bien chiiida!!! o muy guay para que me entiendas.....

MikieD> Yes, that was the manual I was talking about (B64310), as that manual says, Parameter 3404 is the only one that affects the multiple M code execution. It may be that the M codes you are...

What you are doing is the best thing you can do if you want to keep your economy alive.

I work for a pump company in Mexico, all of our pumps either say "Made in Germany" or "Proudly made in the...

Do not despair! It takes a little patience to fix a machine. Check the PMC and try to find a bit in the tool change ladder that checks for a position in the X and Z axes, that is most likely the...

Abundio-

Los post sobre Okuma los puedes publicar en el foro para esas máquinas. Yo tengo 4 de esas máquinas y son muy sencillas (al menos las de control fanuc)¿Que problema tienes para...

Necesitas resetear la posicion de casa. El procedimiento es algo así:

1.- Colocas el CNC cerca de la posicion de casa mecánicamente.
2.- Te vas a modo MDI
3.- Abres el los parámetros (PWE=1)...

Those kinds of restrictions on the machine tool are usually programmed in the PMC. Have you checked the keep relay options of the machine?

I have a brand new (to me) Hitachi Seiki 4NE11-600 with a fanuc 3T control which because of the transportation lost the PC parameters. This causes the machine NOT to start, phase rotation seems...

Thank you very much! I will try it on monday