There may be two excess error alarms. One for moving and one while stopped. Which are you getting and when does it occur?
I.E. If stopped does it occur following a move? If its moving does it occur...
Type: Posts; User: oetkbyentc
There may be two excess error alarms. One for moving and one while stopped. Which are you getting and when does it occur?
I.E. If stopped does it occur following a move? If its moving does it occur...
Try looking at cnc_sysinfo_ex as a start. You may need to combine data from a few different calls depending on exactly what you are looking for.
It will depend on what version control you have. Older controls require several parameters to be changed where the new controls use a single parameter.
Provide the control type and someone will...
You could look at G26 speed fluctuation detection. There are a few parameters to configure for the function but it works well.
There are a few engine manufacturers that require this function to be...
Keep Relays can be turned on and off through the ladder or if the OEM has generated custom screens through macro executer/Fanuc Picture.
Search the address you are changing in the ladder and see if...
You can most likely make them. On the 10/11/12 series I believe the options are set through a mode called IPL which is accessed at power up while holding 2 keys.
Its been a long time since I have...
I suspect much of your issue is caused by the 9000 series which are option parameters.
Not being able to select inch for example is probably due to not having the inch/metric switching option set....
If releasing the Emergency stop button does not do it directly there may be another button (master start, machine on etc) to push. If not there is an electrical / logic issue preventing the control...
1st thing to be done is clear the emergency stop state (EMG). That should clear the reset state and allow you to continue. Depending on the fuse that blew and the cause worst case is some inputs or...
Are there any PC parameter settings in your manual? On that series they would be Diagnostics in the 300's.
Looks like a counter or timer is possibly not set. Its also possible that a value in the...
Each control series (0i,30i,16/18i) has a parameter manual associated with it. Many of the parameters are consistent across the series but there are some differences.
These manuals will also give...
As mentioned, a 25 pin null modem adaptor might work for you. Pretty readily available on line and at some electronics stores.
Ok,
So initially this was started with a lose of parameters.
And now it was mentioned that a new cable is being used.
This adds a definite spin on to what the issue could be.
The cable on the...
those are the areas.. The setting values haven't changed much from one series to another. If you have another manual to reference.
Sounds like parameters.
Hopefully you had a accurate options file to enable Reader/Puncher interface and its just a matter of getting the comms parameters set.
There are a few involved with serial...
After selecting "TAPE" mode via the switch. Does the status display on the bottom of the CRT show RMT or AUTO as the selected mode. It is possibly that the DNC function is not actually being selected.
Are the Z and A axis on a common / dual axis drive?
If they are what is the drive part number?
There may be another parameter involved in case of dual drive.
I think setting parameter 12.7 and 1005.7 to 1 for the A axis will do what you want.
Mill vs lathe has very little influence on the ladder.
Most of the difference between the types lies in the NC program structure.
Try to get a "Connection Function manual" for the control types you...
Possibly a changed keep relay that didnt get documented.
G43.5 in the ladder is what sets DNC mode. Start there and see if what is turning it on.
Another area is the software operators panel or...
Those error codes are displayed through the ladder (PMC) and caused by inputs (X address'). Given there are several and they don't seem to tie directly to one another based on the text, I would...
There are a few different ways M-codes are decoded (created) in the newer ladders. You should try to locate the method the OEM has used and see if the M-codes you want are already decoded.
Just...
There are a few ways this can be handled with various levels of difficulty and power gained.
A very basic example could be;
Look at the ladder for bit F64.2 which indicates that the tool life for...
When you say the axis dislocates. Are you referring to the home position not repeating / not being correct?
If not, could you detail the symptoms a little better.
I believe you can only manually origin the relative positions. Absolute positions can be set using G50 (G code A), work shift, work offsets, or parameters (76,77).
Parameter 12 bit 7 covers how the...
and the diagnostic screen status?
Is Waiting for SAR or Feed override 0 set to 1? Or any of the status items on that screen.
Look at the bottom of the screen at the status bar as well as the distance to go window.
Is there a MTN, FIN, STOP, HOLD, STRT, or other codes present?
Is there a distance to go indicated on the...
Watch the position error diagnostic during the tool change. Hard to say exactly without the control type but I suspect it will be Diagnostic 800 area. They should be pretty stable.
If you see them...
Un mensaje de 2007 es causado por el PMC/LADDER.
Debe consultar los manuales OEM (no Fanuc) o buscar en la escalera (dirección A) para encontrar la causa.
A 2007 message is caused by the...
Does the axis slow down when it sees the sensor?
If it doesn't check the sensor,
I dont recall if the 10 series has the 090 alarm or not. So if the axis does slow down while on the sensor then it...