If you are on the latest version of Pathpilot then you can do this. I'm running 2.10.1 and an not sure if/ which version this was implemented. Here is how I would preform this inspection.
1. Probe...
Search:
Type: Posts; User: wavok
Search: Search took 0.01 seconds.
-
03-18-2024, 12:46 AM
- Replies
- 1
- Views
- 212
If you are on the latest version of Pathpilot...
-
02-15-2024, 02:09 AM
- Replies
- 1
- Views
- 256
How much do you trust the floor of your trailer?...
How much do you trust the floor of your trailer? Is it made out of 2x material? I've seen these machines shipped by removing the feet and bolting through the feet holes or making a cleet that hugs...
-
01-22-2024, 05:26 AM
Thread: pcnc440's after near 3 yrs
by wavok- Replies
- 125
- Views
- 21,990
Re: pcnc440's after near 3 yrs
@metalmayhem, I'm curious about your controller getting stuck at the splash screen and how often your controller loses power randomly? If your controller is being abruptly shut off often then that...
-
01-13-2024, 06:17 AM
- Replies
- 4
- Views
- 332
This doc covers how to replace the battery on a...
This doc covers how to replace the battery on a bunch of the controllers.
http://tormach.com/battery -
01-03-2024, 03:47 PM
- Replies
- 11
- Views
- 915
The spec states 96 but 93 is the actual height,...
The spec states 96 but 93 is the actual height, there is a few inches of head room in the spec in case you have to extend any of the feet for leveling. How much room do you have?
You could probably... -
12-30-2023, 07:24 PM
Thread: Fusion tool library import to Path Pilot
by wavok- Replies
- 3
- Views
- 608
I don't know much about importing a tool table...
I don't know much about importing a tool table straight into PP, however in all the other applications where I have had to convert data from one platform to the other I have learned that the import...
-
12-30-2023, 07:12 PM
- Replies
- 5
- Views
- 443
Provencut is lauded as having specific F&S...
Provencut is lauded as having specific F&S numbers for a 440.
-
09-06-2023, 03:59 AM
- Replies
- 15
- Views
- 1,960
Re: Can someone tell what is this message(alarm)
FWIW I have been struggling for a few days to access my machine and accessing via ip address worked like a charm.
-
09-01-2023, 02:36 PM
- Replies
- 15
- Views
- 1,960
It sounds like you have tried this already? I...
It sounds like you have tried this already? I haven't done it but posting here in case you missed it.
https://blog.tormach.com/connect-your-tormach-to-the-internet-ditch-flash-drives -
04-12-2023, 03:46 PM
Thread: Spindle Speed
by wavok- Replies
- 2
- Views
- 1,010
Ra-bowtie, The probing rough and fine speed can...
Ra-bowtie,
The probing rough and fine speed can be controlled on the Probe Setup tab within the Probe/ETS tab. In G21 the machine will move to the g37 position then use the Rough Probe Feed f
rate... -
01-29-2023, 05:10 AM
Thread: PathPilot ROBOT software
by wavok- Replies
- 3
- Views
- 1,233
Vmax, have you tried the virtual PathPilot robot...
Vmax, have you tried the virtual PathPilot robot edition on hub.pathpilot.com?
You can move a "robot" around, check out the conversational programming and so on.
There are a bunch of PathPilot... -
01-29-2023, 04:45 AM
Thread: Crash course in PathPilot and CNC milling
by wavok- Replies
- 3
- Views
- 1,053
Here is an older video but still very relevant....
Here is an older video but still very relevant. Some of the PathPilot interface has changed but the fundamentals are all there.
https://youtu.be/2EIQo8g4RVQ
This one is a good starter video as...
Results 1 to 12 of 12
