I have no problem running without chiller.
My machine has no spindle chiller, it's been 4 years now.
But I just run small batch , so I never run the spindle continously for a long time ( 60...
Type: Posts; User: mcv300
I have no problem running without chiller.
My machine has no spindle chiller, it's been 4 years now.
But I just run small batch , so I never run the spindle continously for a long time ( 60...
Hi, my machine spindle does not stop during spindle orientation ( prior to tool change or M19 )
*SOLVED*
loose proxymity sensor connector
My table is working with a cnc plasma now, mach3 based.
I want to add oxy fuel cutting to my cnc table.
What is required ? I want to have auto ignition , auto gas open/close and safety is a...
Thank you Jim,
My PM 65 is a mechanized type, I will use the front panel method you suggested .
have a great day :)
Today I get my PM 65.
How to let the gas flow manually ? I looked in the manual , did not find any useful information
With my older PM45 , it can be done by turning the amperage knob...
So you can pierce but you can not get the axis moving ?
Possible problem :
1: arc ok signal cable is bad: check continuity with a multimeter
2: pierce height not correct, pierce delay too long,...
it depend on your gantry weight, feedrate and acceleration.
if yours are low then single side driven gantry is okay, otherwise it is hard to stabilize the unsupported end due to larger inertia
Practically, it is not easy for a stepper driven gantry to achieve acceleration of of 4.45 m/s^2
If you have extra money, buy their servo version
For "torch on" function you need to connect one of the output to a relay
You can split the torch on signal from your BOB into 2 relays, then connect one of them to hour meter
I think this is not a real shop. Beware !
Their address is an address of a high school :
http://budi-mulia.com/index.php?option=com_frontpage&Itemid=1
First, you need to define a set of (jet) tools in sheetcam , basically all are the same except the feedrate and pierce delay
Then, you can import DXF to sheetcam, make necessary operations, then...
I just bought a brand new PM45 for my new table , this is my second PM45
It cuts perfectly, but it shuts off the torch every 90 second during cut, specially at 45A, the torch is off anytime the...
I had same problem, it was solved by testing each ground connection with a continuity/beep multimeter
somewhere in your system , there must be "short circuit " ground connection, it could be -...
Is there any ( free ) software that calculate the line length of a 2D dxf file ?
Hi patriqq,
this is a useful utility :)
by the way,
do you have or know if there is a length calculator of a dxf file
Jim:
As stated in the manual for PM30 consumables , if used with T45M, the cut height is with or without deflector ?
What does it mean "deflector is optional " ?
Thank you Jim,
On page 3-8 PM 45 manual says:
" Unshielded consumables and the T30v ( Powermax30) 30A consumables are also available for use with the T45M "
Please confirm that I need...
I have a PM45 with machine torch, shielded tip , my cuts are mostly thin 1mm MS and SS.
I cut at 30A all the time with PM45 standard consumables , because my machine cannot go as fast as HT 45A...
If you buy cable carrier make sure you buy a size larger than required, the retainer clip will not be easily pop out during motion
If you can fire the torch on air, then MP3000 DTHCII is compatible with it, you just need to buy a DCP ( digital current probe ) and a RAV01 voltage sensor.
I will go with module 1.5 as suggested. thank you
Thank you Fernando,
:cheers:
I want to make a new plasma table, previously I use belt , this time I want to use rack and pinion
Table x travel will be 2500mm, cutting speed will be around 8000mm/min, which rack module is...
I am planning to build another table with rack & pinion drive.
Question : which module is recommended ? 1 or 1.5 ?
the goal is to have precision and repeatability
thanks
Jon
Can I use sand blasting media : steel grit, aluminium oxide etc, as a vibratory tumbler media ?
Thank you Mike,
very valuable information for me :)
If a motor has inertia of 0.2 kgcm^2 paired with a reduction gearbox of 1:10 with 0.1 kgcm^2 inertia
How much is the total inertia now ?
a) 30 kgcm^2
b) 20.1 kgcm^2
Thank you
A friend of mine bought ARTCAM PRO for around $5400 ( Asia region ). The price list is indeed $7500 but you can always negotiate