Hi Lads..
Have a new one. My vf2 just stopped in mid program "No Interrupt" no alarm and screen frozen. Any Ideas
Regards
Pat
Type: Posts; User: tecko
Hi Lads..
Have a new one. My vf2 just stopped in mid program "No Interrupt" no alarm and screen frozen. Any Ideas
Regards
Pat
Hi Mark
OK put about 5 hours aside. Its an easy enough job. One thing before you start Is there a shot pin used to orintate the spindle. This is on the gearbox behind the motor, a small square...
hi
cb4 is one of the brakers on the right hand side of the pannel I think its marked solenoide braker.I dont think you will be that lucky
Hi lo cash
I would check the plug on the spindle encoder is tight and follow the lead down from the encoer i think there is a second connection before it gets to the controle pannel make sure all...
yes you use the top com port on the machine. probably the best thing to do is bring the pc to the machine buy a short cable off the shelf about $3 and set everything up so you can see it working and...
The timing belt is only for ridget tapping in this machine
Ken
No its not through a router you can buy a 4 or 8 way comport rs232 card for your pc about $50 for a 4 port and wire each machine back to each port. you only use 3 wires in the cable
...
Hi Ken
i have 16 machines wired up to 1 pc the longest run is 130feet on cat5e cable works fine using http://www.dncsoftware.net this software. No need to even go to the pc just call the program...
yes Ron its [email protected] .. I havnt got the manual customer lost it it would be great if you could e-mail it to me
Thanks pat
Hi
I want to connect a haas external Indexer, to a Hurco BMC 50 with a max 32 control. Anybody any suggestions. I think the code is m54.. So question 1. What 2cable's tell the indexer to run and...
Here is how to set up a network connection between your Laptop and the VF1:
1 . Setting up your laptop ( I am going to explain with win xp , Millenium is exactly the same but some of the icons...
its a meter that sticks 500 to 1000 volts down the cable and checks for leaks. the cable MUST be disconnected from the drive before testing
get an electricion to megger the z axis cable. if there is a brake in the insulation it can blow the card and this can damage the vector drive. If the spindle drive is braking when an axis card blows...
Hi again
if there are 5 of them they should be wired as follows. one from each phase to ground and the other 2 or 3 across the phases. Just check this with a meter to make sure....
Hi can you take a picture of the componant and post it. If it is what I am thinking it is. It is brown, green or red it would have 300v on it here so you would prob. have 200v on it and soldered...
is it blowing fuses after you turn on the mains switch, or after you press the power up button
mmm
youll fix it, there is nothing in a monitor only money $2000 for a new one. you eather have a dry joint or heat fault. now take a hair dryer and a screw driver to it and find out.. go on be...
They wont. you just wont be able to fix them lol
http://images.google.ie/imgres?imgurl=http://www.opamp-electronics.com/~opamp/catalog/product_thumb.php%3Fimg%3Dimages/UA78M15C_15V_500mA_Positive_Voltage_Regulator_012990.jpg%26w%3D100%26h%3D99&imgre...
Ok, Just to be sure you can take the back off the monitor case and you will see a mains plug on the monitor. Leave the machine on and unplug the monitor for about 15 mins and plug it back in again,...
:confused:
Hi
I want to connect a haas external 4th axis control, to a Hurco BMC 50 with a max 32 control. Anybody any suggestions.
Thanks
Pat
Hi
If it is the CRT type, it is most likely one of two things. One, a dry joint on the line output transformer ( the one with the wire going up to the side of the tube ) or, There is a little...
Hi
just a thought, did you do a ballbar test on the machine? maybe you have a bit of backlash. If you don't have a Renishaw ballbar test, try putting a clock on the X axis touching off the spindle...
Hi Geof
I have all the notes some where how to this. I will post it Later today. Once you do this it will be like a new machine and will start looking for a password after 30 days like it did...
Hi Domb
I know you load the system software through the RS232 port not the floppy. Have you spoken to the guys in Haas, they are very helpful if they think it can be repaired this way they will...
Hi Domb
We replaced the 3 processor boards and had one of the spindle drives repaired the other was replaced. A few PC'S were replaced along with numerous of other bits and pieces, ( Of all...
Hi
I had the little "g" problem on 2 haas machines in the same factory, and it happened after a very short space of time between them. This should confirm your conspiracy theory.
Except within 3...
What spindle drive is in your vf0. If it's a mitsubishi is the run connection reading High ie more than 1 volt
Hi
The solenoid's all go back to a conection block up at the solenoid tower, you need to follow the two wires from the Hi or Low gear solenoid to the block and connect a volt meter, check that you...