So I have an old Mazak m500/50 horizonta,l M32 control ,that has a probe on it, was factory installed , I have all the hardware working but it won't bring up the measure screen when prompted. I'm...
Type: Posts; User: Jfrahm
So I have an old Mazak m500/50 horizonta,l M32 control ,that has a probe on it, was factory installed , I have all the hardware working but it won't bring up the measure screen when prompted. I'm...
What value is D01?
So I have a Mitsubishi mill with a Mitsubishi meldas 520 controller with a 7.2 lcd screen that's dying.So meau has a replacement for it but it won't work for a mitsubishi heavy machine and they can't...
So had spindle rebuilt on Mazak H500 mill reinstalled and of course spindle would over shoot spindle orient and then just slowly , 1 rpm, continue turning. You would think every thing would be the...
Yes, I'm leaning toward the loosing steps direction I looked at the code and didn't see any thing weird. I thinking an optional stop (m1) at each z retract between each letter and measure the z and...
Would probably have to break it into smaller files and send in pieces. So my second question would be what do you do after it cuts to deep do you have to retouch of the tool length, which would be...
If you want to send me the g code I can take a look
So just wondering how your holding the bit is it possible it is walking out.?
So we bought this machine knowing it needed work, it is a very large Mitsubishi horizontal boring mill. So we got it back together now and the mpg handle didn't work so I had meau tech check it out...
Trying to get the low coolant alarm to work. There are two pages ,I believe, of inputs are numbered from 1 to 12on one page and 11 to 24 on the next, so if i want to use the input on line 7 bit 0,...
So were do I come up with the numbers that represent the input and output parameters.
Example IF [[VDIN[1158] AND 64]EQ 64]]NRUN (pick appropriate address in check data - see maintenance...
Well i was going to try this but I can not find the address I should be using I see all the variables like vmcod or vatol and all the other v addresses but where do find 1158 or 64. Perhaps a secret...
Have a MC-80H with OSP 5000 that does not alarm out when coolant is low. The switch is good and it shows on the check data screen that it turns on and off. Possible parameter issue mabye ? I have all...
196222Forgot the screen shot
Installed v11 seems fine but the canned cycles in the cam don,t display properly when opened. Not sure if its a dolphin cam issue or somthine with windows 8 or i'm missing somthing. included a screen...
Will v11 run on windows and if not when? Running v9 on xp on old laptop now thinking of upgrading.
:cheers: Digging through the manuals, operation manual, discovered I was trying to load sdf program with pselect and not sp soft key IE "SS" a.sdf. But thanks for the help.Saw some pallet...
Trying to write a schedule program for mc 50 horizontal with 2 pallets and keep getting programming errors. I assume either syntax or grammer errors as these machines are very picky, for the schedule...
Ok little background first. machine is a tornos enc 264 and has an Fanuc OTT controller , which is basically two OT controls. any way had a servo drive go bad acouple mouths ago. So last week i...
Did you ever find parameters for this machine. I have an amura 1350 which is a da lih.
Sounds like safety is more important than surface finish.
If the pump is three phase check that the voltage is the same on all three legs. If not it will do wierd things with the breakers.If you loose one leg the other act like there shorted to each other.
Have a Tornos enc 254 that started cutting smaller parts the other day all by itself. Had just changed tool and thought it had moved.So comped the geometry and ran about 10 more parts and then it...
Recently bought a this enc-264. I;m in the proccess of getting up and running . Have work through most of it, but trying to figure out how it counts parts and determines end of bar with out telling...
Looking for a manual or any info on a smw fsq 32 bar feeder. Thanks:banana:
Recently bought a tornos screw machine. Has Fanuc ott controller and c series drives. Just got it fired up yesterday and have a problem.(wedge) The drive for chanel one alarmed out. Checked drive and...
I bought two slant 30 atc lathes a couple of years ago one has T3 controller one has T2. Now I got parameters for T3 and its been up and running for awhile now. Now here's the rub I got the...
Anybody know how to connect indexer through rs-232 port, indexer manual shows how on indexer end but I have know idea how to output data through port in automatic mode. controller is 11-m fanuc....
I'm puting a slant turn 30 atc m/c together. I,m looking for a x axis motor,mine is missing completly so i need motor and encoder, and looking for tool holders for the atc. Need a facing holder and...
Just remember experience is something you get right after you needed it.(nuts)