Well all I can say is good luck. I don't know who your vendor is but MLC Cad covers a lot of the country and they sure don't give a poop.
I got the Postability people to see if they could get wear...
Type: Posts; User: John_B
Well all I can say is good luck. I don't know who your vendor is but MLC Cad covers a lot of the country and they sure don't give a poop.
I got the Postability people to see if they could get wear...
Wouldn't have thought that small machine has box ways. Most of the Emco stuff is on linear rails.
Sent from my SM-G965U using Tapatalk
As you are already thinking, check with the ballscrew and linear way manufacturers on compatibility with oil versus grease.
Another thought though is to use a grease pump system. They are a bit...
You could post the document here on CNCZone...
Sent from my SM-G965U using Tapatalk
Rather cheap ploy to drive traffic to your site and make them become members...
Sent from my SM-G965U using Tapatalk
Sorry gents, no longer have that machine and the parameter backup went with it.
Not that you could use the parameters from a different machine though. The Okuma-Howa engineers set the parameters...
There's a machine and control definition to go along with a specific post for the UMC750 available. Just have to get it from your Mastercam dealer.
Sent from my SM-G965U using Tapatalk
So on a DMU50 that toolchanger controls are under the custom menu. There's an icon with a conveyor and tool change arm if my memory serves right. You can return each component to the default position...
I think the circuit you have that wired into might be a bit weak, could be you're getting a brown out condition. Memory serves that you might be 20 amps or so low.
I ran one for years that had...
Well there you have it, the all knowing has spoken. Don't dare take anyone else's input, he has experience beyond all others combined and you must emulate him in all ways.
Do you have any time to possibly steer that in a different direction? Mastercam has become so big ridden lately you have to keep 2 versions running on your computer just to get the job done.
...
Again, anyone with a similar machine that can offer insights please chime in!
I never really used coolant on the sub-spindle, and if I did I don't know if I ever checked to make sure it was...
Just in case this helps someone else... it's fixed now. It was a break in the signal wire, apparently about half way back to the control cabinet. Sucked finding that and replacing it and running the...
I think you're the target audience for their courses, and those of caminstructor and the other independent ones. They go through how to use the software and what the buttons do pretty well.
The...
When picking points for the dimension press the "I" key for intersection, then pick the lines that would be projected to a point were that radius to not be there.
Does anyone have a similar lathe with 2 spindles and the Siemens 840C control, that can help sort out the sub-spindle clamping signal issue I'm having. I just changed it over from a collet chuck to a...
You're in luck with the 840D control it's pretty easy to monitor the feed and rapid override status, unlike the Haas control. Contact eNetDNC or any of the others advertising and they will data...
You need a DNC program. Hyperterminal on older PC's will work, not sure if it's still built into Win10.
A cheap or free program is Codeshark that can be found on the web. Many others out there......
My question was more about the lathe side on Fusion360. I've tried at length to work with it for my lathe and consider it almost unusable.
Sent from my SM-G920V using Tapatalk
Are you saying you're using Fusion 360 for lathe and it's working well? Or for mill?
Sent from my SM-G920V using Tapatalk
You've got PM's blocked.
Sent from my SM-G920V using Tapatalk
X9
Sent from my SM-G920V using Tapatalk
Amada
Sent from my SM-G920V using Tapatalk
Takes a lot of getting used to, but then I don't have experience with any others. The sub hand off gets screwed up to often, and alot of other glitches. In my opinion Mastercam hasn't spent a lot of...
Uh, travelling to Germany... maybe Siemens?
Did my internship with Siemens KF, and do know they have a repair division for control and drive products. Check with them before you travel maybe...
...
No, don't have one for lathe. I don't have the mill anymore either. 8 years later, so lots of things have changed.
Sent from my SM-G920V using Tapatalk
That is very similar to a face mill. Try using that and adjusting the dimensions and corners to look like your tool.
eapprentice.net
No relation, just would recommend over the Mastercam program.
Sent from my SM-G920V using Tapatalk
Mike,
No, not familiar with the Hitrol - just got a slim grip on the Siemens programming. Sorry
Sent from my SM-G920V using Tapatalk
Mike - did you get it figured?
My machine with the 840c is an Emco Maier with twin turrets and spindles, so it programs a bit different- but I've pretty well got it sorted. I'll try to help...