Search:

From NC software 340 49x-07 with cycle 290 interpolation turning ( option96)

Hello Heiko

I would suggest you to necessarily make a course.

With best regards, Schabi

Hello Appenzeller.

Are you sure that you only have 2999? There’re about 100000 in the demo.

Regards, Schabi

Hello
It doesn’t work because the 355th works in the background.

Greetings
Schabi

Hello willi1681

The 530th has a button “add N lines at the end” on the second softkey level.

Greetings
Schabi

Hello ideefix

We mainly use smart.nc when we have to program dxf-files or units with many pockets, islands and bores.

Regards, Schabi

Isn’t a 10,4” display kind of small?

Hello Felex

It works without any problems in my case. Just download the last version.

Regards, Schabi

Hello
Today I tried to set the feed override more precise (now 1% pitches). I set 7620 in MP on non-linear characteristic line but it was unsuccessful. My question is where can I set the size of a...

Hello
Mikron HSM 400U and Fehlmann P60-HSC are good for small 5-axial units, too.

Greetings Schabi

Hello Conny

Yeah just with Tool call. Anything else isn’t necessary.

Regards Schabi

Hello
In the mode program-test you have to press the key “choose display split” and then choose graphic. Now you have only cinematic chosen.

Greetings Schabi

Hello
There’s a possibility to search for bores without clicking on each of them in new DXF-converter.

Greetings
Schabi

Hello FireLee

You can make it with the cycle 427. The measured value is stored in the parameter 160. You’ll have to write it into the table of zero points.

Greetings
Schabi

Hello paradox

Go to the list of zero point (or however it’s named) and then edit the current zero point and insert Z100 into the parameters (second register card).

Greetings
Schabi

Hello
What machine do you have? It depends on the manufacture.

Regards, Schabi

Hello Pumuckel1974

Is it possible that the center of the circle (clause 20) is wrong?

As FK:

0 BEGIN PGM Uebung10 MM
1 BLK FORM 0.1 Z X+0 Y+0 Z-20
2 BLK FORM 0.2 X+150 Y+150 Z+0
3 TOOL...

Hello Holger,

I don’t know any possibility because the controller doesn’t have the function FN 18. I neither know a parameter therefore, such a one as for radius.

Regards, Schabi

Hello

Manual mode -> preset-table -> change preset -> add N lines at the end

Regards, Schabi

Hello NLZ

There must be a file PRESET.PR in the folder TNC. Could it be deleted or moved?

Greetings, Schabi

Hello
It must be TNC. Unfortunately I can’t have a share in clarification of the question.

Regards, Schabi

There seem to be problems with FK-programming.
I imported your dxf-file in the demo of iTNC 530. But I didn’t know where the zero point had to be because I saw your program too late.

Regards,...

Hello

I converted it with demo and made an example.

Regards, Schabi

Hi

Don’t you have a high feed motion cutter? They can well work with hard materials and have suitable holding time.
Regards, Schabi

Hello,

I can’t imagine that the nose angle affects the graphic. It’s only for depth calculation required.

Regards, Schabi

Hello!

Can anybody tell me how I can deactivate feed motion and rotation speed override at iTNC 530?

Regards

Shabi

Hello Chüzu,

Form C is without attachment and gripper flute, as far as I know.

Regards

Schabi

Hello rookie,

Only smarT.NC has this function.

Regards, Schabi

Hello,

The rod gripper from Zürn is good too ;)

Regards Schabi

Hello,

No, it isn’t. Sorry
Regards Schabi