On an AC machine , I would think it would be fruitless to do so. They were offered on older dc machines to bolster accuracy , But they also caused many problems.
Type: Posts; User: dunnitagain
On an AC machine , I would think it would be fruitless to do so. They were offered on older dc machines to bolster accuracy , But they also caused many problems.
I've done the automation direct , power supply, 75$.
You need a Lathe
I don't think the All in 1 board will work , my servo are 40 Amp Glentecs and the All in 1 only has 20 Amp output.
I spoke with the Retrofitter that did the 3016 , and he is going to email me some...
I'm looking to replace a dead control on my Fadal 6030 1993 model with DC brush servos. I have a few questions for the forum .
I would like Full 5 Axis capability , ( I have the Equipment ) but its...
I agree with the Delta Tau Products, they are top notch. I'm looking to go with a full Centriod Retrofit . The Camsoft deal is based on way to much Sales BS and not enough hard Documentation.
One of your sensors has a metal chip on it . The Proc sensor cant read its position so it faults. Clean out the Carousel with a blow gun and try again.
Been screwing with this old girl to long now. My control is excellent but the dam motors and drives are to problematic.
Any suggestions for some good motor-drive retrofits for the Glentek 6000...
Hey G59, The motors are the originals but they have been rebuilt a few times. A well known parts supplier sold them to me 3 years ago.... now I find out I should of bought the Glentek 0021 . I see...
Hey Y'all . Is anyone having issues with the AMC-0015 Amp Cards? I have 2 on a 6030 DC machine Yand Z axis. I think they have both died. Now after researching them, I think they are too small
for...
Hi Russ, No not yet , Thinking of selling for parts.... What would a power automation setup cost? I really like the Numatix features but being tied to one source for service.
Really is a hold up . I...
Hi Russ , I think I've purchased Fadal parts from you guys before! I,ve seen that Power Automation control and I looks nice . I would like more info on it . I'd really like to use my existing...
Been there done that with Carlo, I don't have 5000.00 just for a software upgrade.
Just looking for something more reasonable than antiquated proprietary software that's supposed to be open source.
Hey All
Well I powered up me new to me 6030 with Numatix retrofit ,and as soon as I hit the key that powers up
the drivers in the control. All Three Axis run away at full feed rate. The only way...
Hi Tom, I can get you specifics when the machine shows up at my door, I appreciate your help . Thanks
I've just purchased a 6030 with DC drives and linear scales, The machine
already has a numatix retrofit on it. That control has become increasingly more unstable
and occasionally crashes the...
Ive just purchased a 1993 Fadal 6030 DC with scales and a Numatix control.
Previous owners said control works good, but is very glitchy.
The control uses an obsolete Delta Tau PMAC , and retains...
Here is a link to pilot001 reply to another post. Ive since lost all the documentation to the parts sorry Problem DC Servo and Amp Repair - CNCzone.com-The Largest Machinist Community on the net!.
Hello all. I have V23 and V24 seats for sale. Dont use them .I have 23 with Lathe and Mill and training vids, V24 with lathe and mill training. PM me if interested.
We are in North Carolina.
Hello all. I have a 93 model 6030, with a Numatix control retrofit. To make a long story short. Is there a way to tune the servo PIDs with an oscilloscope? The retrofitter told us that the servos...
What year is your machine? Some of the old machines oiled the x ballscrew,by the way oil that bypassed through the turcite on the back right of the table. Consequently the ballscrew ran dry or not...
We hung a Gateway FPD 1730 right on the front of our MP32 on a 2003 6030. Just plugged it in and away you go.
The AMC amps are just as good if not better than the glentec and almost half the price. I replace all my glentec stuff with amc when they go down. The glentec amps have alot of proprietary labeled...
Sounds to me that you have a tach wire broken or shorting in the motor. I would do like the previous post and do a megaohm test on the motor . (Your local HVAC guy might loan you his megaohm...
I agree with D.D. Ive seen one like that with an auxiliary hydraulic unit that was used to clamp the chuck.
Thanks for the reply Al. The transistor you pointed out is a darlington. With the case form TO-204 ( I think ).My IGBT form is a TO-247. With the single mount hole. I appreciate your quick reply....
I'm back for more Knowledge from the Fadal experts! Does anyone have a part number for the power transistors on a Glentek Amp -0008.This is a DC Amp from a 93 model 6030. The old transistors have a...
If it is a two speed spindle. It could have coolant goo on the belt. Kind of makes a funny noise as it runs across the pulley.
Andy. If the brushes are almost new then don't worry with sanding them flat. I would'nt waste time trying to sand a concave surface on them either. Most the rebuilt motors I've looked at, that have...