Search:

Sorry for this late reaction, but I was busy with other things.
In fact I did not do anything with steppers and routers for the last 3 years.
I found the function of the connections by reverse...

Hello patriciooholegu.

The pictures are not from Corbo but from me, AbSat. I am not shure if I had contact with Corbo because I exchanged info over email and I do not know if Corbo was one of...

In the attachments a picture of the driverboard I found and a schematic of the input functions I found. With these info a few members got there steppers running.

AbSat

Sorry with that I cannot help you.
I never build out a screw.

AbSat.

There are 2 types of motors to move satellite dishes.
The first one is the actuator from the first item and the DiSEqC
motor I think Al The Man is talking about.
A actuator has a 36V DC motor and...

Hello murray.

I still have, so send me a personal massage with you email adress and I will send it to you. You can have it in .sch so Eagle format or as jpeg.

AbSat.

@bob.

I will mail you in Dutch.
But we had email contact till 05-03-2006 and we exchanged several schematics and pcb layouts.

AbSat.

Hello Isaak.

I think you made a good choice. Specialy when your control is not done by a CNC programm a uP is more flexible.

Succes. AbSat.

@Isaak.
I build a driver for a friend who salvaged a pcb with 3 SLA7026 drivers but no translator.
I put 3 times a L297 on a board to be controlled from a printer port by Mach 3 or Turbo CNC and...

@ Konstantin.

I see no problem in the wiring.
I should connect the sync in/output of the L297 to +5V to make sure that the chopper part of the L297 is disabled. For stability reasons I should...

@box1sa.
I think your question is not related to this topic about the STK6713 so please open a new topic and give detailed information about your motor and the software you want advise about.

A...

Hello Konstantin.

Can you give us the connections you made between the L297 and the STK6713?

I took a quick look and in my opinion it should work if you make the following connections between...

Sorry faruqx but I do not have any schematics.
I have a few driverboards salvaged from copiers with the EICO 231 EICO 241 chipset. If you have the same driverboards I can only give you the signal...

These motors are no stepper motors but simple DC motors.
When the actuator has no DiSEqC control there is no electronics involved,
just a 36V DC motor and a reed contact or opto device to give...

I tryed to build a 3 phase stepper driver with the HIP4082 but stopped trying because too many ic's got defective during test. I used isolated floating supplies for the highside driver. Under low...

Nice thought, never came to my mind.
I have no experience in this field but I took a look in the datasheets of some BLDC driver chips and the following questions popped up in my mind.

What is...

I build 3 phase drivers with the HA13532 controller from Hitachi and the SLA6023 driver. But both saved from dismantled kopiers.
stragenmitsuko programmed a sequencer for a 3 phase star motor in two...

I did a short test with the SLA7024/26 driven by a L297 and that worked.
I used the chopper from the L297 but did not perform a complete test under different load conditions. With a L297 only full...

Does somebody ever used the HIP4082 mosfet driver ?

I want to build 5 half bridge stages for driving 5 phase steppers with this mosfet driver. But I could not find out if this IC will work in...

Kreutz, do you know a store where I can order these ic's for numbers below 10 ?

AbSat.

Hello corbo.

Yes that seems the same driver board I have.
I send you a PM with my email adres so we can
exchange info.

AbSat.

I have some 5 phase steppers too and I was able to save the drivers also, but they are build with EICO VEXTA chips, the EICO231 and EICO241 as controller and the SLA5011 SLA5011 pair as drivers. I...

I build the drivers for Aanrips router, which is now mine.
The motors where saved from Konica copiers and we took the drivers and controllers from the original driver board. Because we have more...

3 wire steppers are most likely 3phase steppers like the KT60 series from Trisyn.
I use this steppers on my router. They are saved from copiers and we were able to save the driverboards too so I...

I used my soundcard a lot as a oscilloscoop. But keep in mind that it is only usable for Low frequency AC signals. I used it for all the lf signals we transported over normal telephonelines. The use...

I am not familiar with the Berger Lahr motor you are refering too, but we are using KT60 Trysin 3 fase 0.6 dgr/step motors and they are running verry smoothy.
I build the drivers myselft with...

I think with that manual it must be possible to connect the driver to the parallel port. It looks as if the inputs or opto isolated, or there in the manual some specs on the inputs, volts and...

Can you place some pictures of the boards?
Maybe by knowing the chipset used for the drivers can help you any further.
I have some 5 phase driverboards laying around, from some I know how to...

Hello RikkieV.

Sorry that I cannot help you with documentation about the LPKF router.
But I have a some expiriance with 5 phase drivers so maybe there is a link and, I am also from the...

Do you have some more info on the driver ?

It are the isolated inputs of the driver. Most likely optocoupler inputs.
But voor the requested voltage and current we need some more info about the...