i'm sure this is a issue more people have had.
i had to do a clean install of windows 7 (32bit) because of issue's with visual c++ file missing.
i then installed mach3 again.
before i did i took...
Type: Posts; User: cruz03
i'm sure this is a issue more people have had.
i had to do a clean install of windows 7 (32bit) because of issue's with visual c++ file missing.
i then installed mach3 again.
before i did i took...
Hi everyone,
i recently bought a cnc plasma table with a drill head.
i cut a decent amount of 20mm (little more than 3/4") steel plate, with the holes ranging between 14mm (9/16") and 25mm (1")....
i bought the table from a company who made the machine, but they are no longer in buissines.
i don't have the know how to install new drivers.
on the thread i linkend to alot of people have really...
hi everyone,
i have a plasma table with nema34 motors on it.
these have at certain speed vibrations.
i would like to add some inertia dampener to help that.
here's where i got the idea from:...
the drivers are all the same: ACT DM860 finest what china has to offer...
all the dip switches are set the same for the 2 drivers from the Y-axis.
oke, but when i did that and i calibrated the axis in mach3 i got the twisting problem.
when i put the gear reductions in, i tried it first with the original drivers setting.
then i calibrated the...
well the reduction that i have now is 5 to 1, if you give it 100 rpms it gives 20 rmps out.
so with what you're saying, i would then need alot more steps/rev then the drivers can give.
i think...
Yes, I now have 25000 steps/rev.
I thought I would need less steps with a 5 to 1 reduction. Because with then you can turn the shaft with less steps.
Or I'm completely wrong there?
That's why I...
okey, today i messed with it alot, to the point i got tired of it and removed the planetary gear reduction.
and after putting the drivers back to the old settings (25000 pulses/rev) and...
https://www.cnczone.com/forums/attachment.php?attachmentid=411454&stc=1https://www.cnczone.com/forums/attachment.php?attachmentid=411446&stc=1https://www.cnczone.com/forums/attachment.php?attachmentid...
i don't really know that, like i said i'm really a beginner in the cnc world.
then machine was bought from a company who no longer is buisiness.
here are some pics from the drivers and break out...
Here the picture. https://uploads.tapatalk-cdn.com/20190203/b1ebca32111e546bd42f119b1cd93939.jpg
Verstuurd vanaf mijn ONEPLUS A3003 met Tapatalk
Okay but don't I need to enable the a axis then? I've included a picture of the pin numbers. I would need to use the numbers 8 and 9 then?
I'm a novice at best in this if you didn't notice :)
...
Well seems like my machine doesn't use a slave axis.
In the motor output page there are only 3 axis enabled x y and z.
Now what :)?
okay, here's my stupid question of the day:
do i check it in the slave menu, or how to check with 100% certainty?
I never looked if there is a slaved axis, neither did I change any settings regarding that.
Could the problem maybe solved by slaving one of the motors?
Verstuurd vanaf mijn ONEPLUS A3003 met...
correct me if i'm wrong, but don't believe that there is a slaved axis.
the machine has 4 motors (2 for the y, 1 for the x and 1 for the z) and there are also 4 drivers.
that leads me to believe...
hi everyone,
a few days ago i added planetary gear reductions to my Y-axis (the axis has 2 motors, one on each side).
it's a 5/1 ratio and the machine runs smoother with it, and if a can get it...
has nobody any idea's or suggestions what the problem could be
here's a link to a video while the machine is running:
https://mega.nz/#!GPJwwSIb!Bv8JHZdQeZlQxiIN2HkhzpL6Uw7PpuGR1rmypSnujMI
some...
hi everyone,
i've noticed something with my plasma table,
when cutting something with a "lower" speed the torch and torch mount vibrate.
this is only noticeable when it's moving in both (x and...