Search:

Yes we do, let me know your E-mail address so I can E-mail you a quote
Thanks
Ahn Vuong
[email protected]

Hi Jarno,
I think your spindle encoder is defective that is why alarm 409 (SP=47)

Ahn Vuong

wow, when I answer you it was 3 years ago and you just look into this problem? that's ok, I just wonder

Spindle amplifier alarm 09, you should check the cooling fan on top of the amplifier.

Press RESET + FEED HOLD to reset alarm 1001, but make sure to grease all three axis after reset alarm

Ahn Vuong
[email protected]

You should look into eBay, a lots of used or new there

Ahn Vuong
[email protected]

Press RESET + FEED HOLD to reset alarm and make sure to lube all axis after reset alarm

Ahn Vuong
[email protected]

the two trust bearings is loose, lock it down and it should work
Ahn Vuong
[email protected]

As far as I know this ML-25A can't stop spindle in the exact position and it did not have the M19 funtion either, some other ML-25A has the M19 but soon you change the mode selector switch M19 will...

It is an automatic tool changer home position
is your VMC with ATC?
Ahn Vuong

I think you should look into the ATC home position signal, if the ATC home position not made than all three axis can't be move

Ahn Vuong

Just wonder, did you call M5 before M41?
Ahn Vuong

401 Servo alarm, I think you should make sure the optic cable plug in properly
Ahn Vuong

I am sorry don't know much about 5T or 5M control, but I think the switch is locate on the Motherboard or Memory board in one of the electrical cabinet, may be someone can explain better than I.
Ahn...

the selector switch should be in Edit position and also need to turn on the write enable switch to edit or change any data
Ahn Vuong

the blank one are all zero

Ahn Vuong

Hello Parker,
Attach file is the parameter you are looking for, hope this help

Ahn Vuong

You are welcome, contact us if any more question
Ahn Vuong
[email protected]

Do not call M06, this machine won't take the M06 code, just call T500 or T600
and it should work
Ahn Vuong

sorry I don't have the PDF manual but you should check the EM switch and over travel release switch
Ahn Vuong

I think you should look into the PC COUNTER page and under the CURRENT to reset the value
Ahn Vuong

sound like a fuse blown?

Hi Samu,
If the Koyo one you purchase doesn't work make sure to contact us. by the way you may want to know the parameter for Spindle orientation position, if the position is off you can change the...

The one I offer you this morning will work for your machine. guarantee
Ahn Vuong

Try the list of parameter as follow.
6572 change from 900 to 3000
6536 change from 0 to 200
6537 change from 0 to 6000
6583 change from 96 to 70
6603 change from 400 to 200
6611 change from 100...

More shaft showing which plunger will go up higher when pump, mean more oil

Ahn Vuong

Is your machine lubepump look like attach picture? sound like very close the same, this lube pump if you need to increase or decrease lube oil, just break loose the set screw on the plunger and...

Is your machine below the oveload has one of the Spark protector like attach picture? if yes you may want to disconnect it.
Ahn Vuong

unfortunately you can't do that, because your spindle RPM will not be correct.
I seen it before when the encoder getting close to fail it will do that but it will get worse and worse.

I think you...

Is your machine look like the attach file??
Ahn Vuong