Search:

Ok I have the 900 parameters reinstalled ( called the machine seller and got them over the phone ) . Everything works fine except the machine will not cycle start . This is also the case with MDI . I...

Yes Krazatchu I would love to avoid the DIY . That is why I am here to pick the brians of the more knowledgeable .
So in converting the AC to DC will I lose amperage or will I gain like on the...

My guess is that you have your G2 and G3 backwards judging by your numbers .

What I was meaning was how do I access the 900 parameters to be able to reinstall by
manual input

I did not think that this was important since it was a control issue and not a machine specific issue .
The machine is a First CV 410 a very basic new in 1984 machine . No tool changer no...

So I will need to get the factory spects from Fanuc is what you are saying

The PM has been sent Al , Where do I find the 900 parametrs ?
If necessary I will copy them out by hand and install them

Hey guys , I made a big error today and pushed reset while I was powering up the machine and cleared my parameters , Now I was smart enough to back these up quite awhile ago .My problems starts with...

Thank You

Quick question AL explain power . I know what amps are and I know what voltage is .
But the translation to power is ? Horse power . By the way thank you for the reply I do appreciate the help...

Ok AL I am really new to the electrical side of things . So to simplify for me
you are saying if I have 12 volts and 60 amps and I increase the voltage the ampeerage that I can draw upon will go...

So I could use a power inverter and change the output to DC by doing the same as a car alternator ? And what do you mean current going down is this what they mean when they measure amps ?

I have a general question about amplifiers . Is it possible to turn 12 volts DC into a greater voltage ( like 48 or 96 or 108 volts)and where would I find such an amplifier or do I need to have one...

Does anyone have experiance with a Fanuc OM and a pallet changer .
We have a Kitimura Mycenter with a pallet changer and a OM control .
I have the paperwork from the machine builder but the...

I also tried it and was not worth the money spent , better to spend it on a good website and advertising in the yellow pages .

Sorry guy but I only get one layer for your print .

Looks like it can be a good job but you will need to break the dimension lines off the part in the print so I can tell where the part ends and the dimension lines start .

Hello I am Machinist who is about to lose their shop in Ont , Looking for a full time job with an established company . I am also willing to bring the customers that I have with me to the right...

Plan well stick to the plan and make sure you have enough funds to start .
I started with next to no money and it has been rough .

Not sure , but when I worked as a toolmaker I was expected to do the same .
Sounds like you work for the same company I quit to start my own shop .
LOL . As for expectations depends what you...

I understand where you are coming from just trying to give you some insight from my own experiance with customers . Just be prepared to explain why you are so cheap or why you are expensive . It will...

I agree makinoman keep this under your hat at work , what happened here is nothing to the harrasment you will get from your co workers and boss . All the power to you and remember if you are to cheap...

You guy's have totally taken over this guy's thread .

Thank You for your replys
I am going to close this RFQ now ubtil further notice .
I will make a better print to quote from .

OK when I get a few minutes I will try to get on creating a print that can be understood

Ok here is a picture it should be worth something I only want the body turned with the grooves for cooling . I will mill in the middle grooves and deal with all the tapped holes . Forget quoting the...

Sorry guy's
I will post a picture of the finished unit .
Tolrences are +- .010 except for the oring slot +- .002
This is a turned part with 6-32 tapped holes on either end .
the grooves are...

I need a quote on the turning , Main body only . Also a quote whole job
quantity of 100 . 500 per year .
Material 6061 Aluminum

You have PM

I have a First Cv410 with a Fanuc O-m and tool changes happen on M10