Search:

Hi Tom

I received my new replacement board today, had everything already pre cut and ready for installation, and sure enough it is alive again all functions and limits are working.

Have to...

HTH

Yes the Led on Kanalog board comes on, reading on voltages are all at 0.51vdc and does not matter what dac# =value I send them, no change on readings.

Regards
Mac

As far as the switches they are all Prox and they all work fine and if removed from the distribution box no difference in effects

I can power the encoders without powering the servo and can check...

Using Parker Servos and kanalog/kflop +/- 10 volt analog setup for years, but recently on power up, the mills 3 axis's all take off (~ 20 inches a minute) in the negative direction till hard stops...

Thanks for the reply but I think we have a misunderstanding what I attempting to do. I'll try to explain it another way.



C axis rotates around the Z spindle axis
B axis rotates around the Y...

I have two separate applications needs, One is a standard gantry router style machine that Id like to be able to add C axis capabilities only using (Y or X),Z and C axis. Size and accuracy is always...

Thanks that helped to understand a little about the need to edit the post.
But I'm still fighting how to setup the 4 axis settings
I've circled a few issues in this screen capture.

224534

How...

Thanks for the link, I like it for clarification of a few questions I had on 5 axis setups, but still does not address how to setup a 4th axis "inline" with the spindle. I can lie to it to get it to...

222898

222900

using the spindle out of alignment trick, I can manage to get it to rotate in "C" in the 5th axis mode using the "5-axis Trunion_Machine" option
just not found a way to do it in...

222886

setting in the 5th axis options
if I set the spindle axis to .0001,.0001,1
I get past the error of alignment
but the issue, is it does not rotate around the C axis then.

222890

222880
(just a quick sketch I created to see if I can develop a 4 axis post setup)

can manage to pick a 5 axis post so I could show the C axis rotation
Just can not get the tool to work only in...

Thanks for helping.
I have full 5 axis multi version.

Using 4-axis functions (simultaneous 4-axis)
Origin(0,0,0) Direction(0,0,1)
I get the message:
Error! The spindle axis is parallell to...

With over 100 views and No responses, Does that mean it is not possible to setup MADCAM to use the "C" rotary axis with the "Z" linear axis?

Is it possible to setup MadCam to use a 4th axis rotary table sitting on the "XY" table of a vertical milling machine. I'd like to side cut some multi lobe Cam profiles.

And is it possible to...

I have seen several version updates but this has never been addressed. Any idea when this might be implemented?

I have wired 4-7 for the encoder, but still can not seem to get a feedback signal to a Dynomotion Kflop/Kanalog board. I can move the drive with voltage/DAC output commands. Can send it commands for...

I keep reading about a custom dll can be created for your own needs.

Where do I find a dll source code example, other than the help file example that can not be used?

What software program and...

That is exactly what I am referring too!

Thank You for understanding my post.

Looking forward to the future version that will give me several more visual options that would reflect the actual...

This is the icon I am referring too.
Id like this to reflect the representation of the axis directions.
Where are the images found so I can edit or create the new axis choice.

Changing the...

Where would I find the dll file that would be right for my application?

Or can I edit a dll source file and recompile to a file of my needs?

I have to assume the simulation graphics are...

How do I set up the graphics and post for a Y-B rotary trunnion table? The only option I see is X-A rotary. There must be a way to change the orientation both graphically and for a particular setup I...

That has to be the best use of a bobble head yet.

Cool new addition to a fine product line.

Used on the Gemini GV series DC servo Drives I am looking for a setup, programming manual for the Part# BB-GEM-1 Rev B and the DBIA Trilogy Systems Interface box. I tried Parker Motion but they could...

Don't you have to have a G43 when using a H tool offset Z position?

G43H1Z1.

Where is it at? The file is missing!

Its up for one day and you start to complain and then pull it.

Give it some time. Takes time to evaluate, and then respond.

You can fill and change variables with a G10.
Multiple If statements check the inputted part number and fills the variables as needed. Then these are used in the subroutines. Its just a matter of...

After doing some more reading it looks like I can create a menu and the operator types in a number from 1 to 59 (in my case so far). It runs a script that does some calculations and loads values in...

I would like an example of how to create a screen for a 21i controller, that uses the arrow keys to scroll to a part number. On selection it would preform an angle calculation based on a couple of...