Search:

Leaon fixed me up in two minets it was just a bad u.s.b. to cerial port adaptor
I freek out easy because I have forgoten how to live without my plasma cutter.

My motors shut down constantly and give me the code invalid echo response this is a new problem and I have changed nothing.
It happens with x or y movement if I'm cutting or not but it don't seem to...

WOW Thank you for taking the time to respond in such detail, even I can understand what your talking about.Your right my machine works fine it just bugs me that its not quite were it should be and I...

Thank you for your reply Jim I have had Dynatorch check my controller thay say its ok and set for 50 to 1
if I cut 3/16 plate at 70 i.p.m. with 45 amp and my hight control set to 100 my torch is...

You should be able to go from the interface plug on the back of your pm 85 to your conteroler witch should be factory set at 50 to 1.
then set the scaled arc votage on the torch tab to 6.
this...

I am thinking I will epoxy the lettrs to the plate then pin them just to be shure then epoxy primer and two part pant I would use powder but the epoxy will not take the heet and I don't know another...

I have only cut hot rolled steel on my table .will cold rold cut the same with the same settings and is it hugely more expensive
I need to attach 5/8 letters to 5/8 plate I thought I would epoxy...

I found my problem so I thought I should post it stupid as it is.
When I wired my table I put in a sub panl with a circuit for my pm 85 and a second one for the controller looked good to me.But when...

I use my dynascribe to engrave scraps of stainless with my business card it seems to work well.
When I fist got it ,it would stick and not vibrate some times but when I ajusted the strike foce the...

I have a pm 85 with machine torch diameter is 1 3/8 inch my holder has a notch for the gear rac to clear the rak is 1/4 inch wide and runs 8 of the 12 inchs down the back side of the torch.

Hello John
I am a Hypertherm user in Canada I think Hypertherm is a grate product I have a hypertherm 85 air plasma on a cnc machine maybe some day you will be able to help me. good luck with your...

Thank you Magma-joe
My stop at lost arc is un checked so if I lose arc the drives keep moving.
Another issue I have is my arc voltage reading is way out maybe 20 points.
I am reading it off the...

Your cooling fan was enough to cause an e-stop to occur man that must have been some hard to figure out.If I ever get this bug out I will post what it was.

The system estops. I have never been able to run with stop on lost arc checked.So I guess 65 amp is max. for me. Thanks for your time Tom I hope your new drives work out well for you.

I am trying to cut 1/2 inch steel with p.m. 85 set at 85 amp using the recommended settings but my drive motors keep kicking out maybe 3 times in a 1 foot square it restarts no problem and seems to...

I just cut a scan and I am NOT a computer guy I just scand the image and traced it with cutting shop I dont know why but I had to scale it but the cutting shop software makes that easy.
...

Thanks for your help one again Tom
The 85 is still in my dreems I am cutting with an old 1000 but I want to upgrade before to long.
I thought it would be good to go a bit bigger than I need on the...

Inrersoll rand mod D42IN 25 cfm
Can anywon tell me would this be a good choce of dryer for hyperyherm 85 on my dynatorth table thank you for your time
...

Magma-joe
Thank you I will pick up some silicone spray.
Your table is a real thing of beauty one day I will remount my scribe as you have done.

I have been spraying my rack and rails with W.D.40.
should I be using heavier oil.
I took the air line off my scribe and gave it a shot of air motor oil.
good idea or bad?
What should we do to...

Thank you all for helping me out.
It seems there is nothing so stupid that I will not do it yep
I had use thick material pierce settings checked.
Made a few cuts everything is working fine I'm a...

It's a Hypertherm 1000 .
Today I noticed when the torch fires the z axis lifts maybe 1/4" or so then moves down to cut hight .
Is that normal?
It does it whether the thc is on or off

Thanks for your input Mike
I have been thinking its mydynatorch install but maybe its my plasma althoe it was working fine by hand.
I am afrade I'v done somthing stupid on my setup but I dont know...

New machine and I do not know how to run it
Thought I would start with somthing simple just a few letters.
The torch comes down finds the plate rises to pierce hight fires does the pierce and goes...

I got my fan uesd from a commercial refrigeration outfit for 200$ 1ph 1phase
seems to work ok

I made the call to Dynatorch and thay took the time to help me with the setup everything seems to work fine I have made a few cuts.
only thing is I also must run with stop cut at lost arc uncecked....

I used hevy walled tube for my rails.
The conners have a large radius so when I screwed down the rail it did not sit square. I did a hay wire repair buy putting a set screw in the radius at each...

the overhang on the gantry is to run the torch out over the tubing cutter.
I thought I should have that because I use a lot of pipe for chain link fence.
It may be good for coping or address posts...

yahoo!
My gantry came and it looks like it fitts the table

.