I could be wrong here, but my understanding from a mold builder friend of mine, the accuracy required is very substantial.
I haven't seen a router that has the rigidity to be that accurate.
You...
Type: Posts; User: Heavymetalcnc
I could be wrong here, but my understanding from a mold builder friend of mine, the accuracy required is very substantial.
I haven't seen a router that has the rigidity to be that accurate.
You...
Its always the simple things you feel everyone should know. So here are my stupid questions.
Did you bypass any of the safety locks?
Is the control in edit mode?
Did you reset before you tried it?...
I've had the luxury of working in a very large machine shop for over 20 years.
Management understands the need for good tooling.
We are constantly testing tools against one another.
They set it...
My experience with Kennametal has always been that they have the very best turning inserts in the world. They are still working on milling.
Sandvik, to me has the best milling cutters out there...
I would go with the WMD20 if it was me. Nice big table. It appears to be a G0704 clone. Probably all made by the same people.
I'm not sure the controller board will make a difference. Mach 4 is...
My experience with them is they work great when new. They don't age very well.
But I'm in the camp of there is Kurt, and then there is everything else.
Swarfmaker,
You know you can go back and find all of the old commands, put them up on the bar and use them instead. I still use the old thread mill command. It just works better than the new one....
It used to be called 2d snap. If you are trying to select the edge of a model and have it come out at 0.
Before you select any edges. look in the top left corner. There is an icon that says 2d....
I'm sorry to hear you had fitment problems with the kit. I know I talked to you about it a little bit when you were installing it.
I'm trying to get another machine to check everything and make any...
Here is something I've always liked doing. Especially cutting aluminum. I use an end mill with a radius. Say .062". Set D.O.C. to .04"
Run max spindle speed and max feed that the machine will run....
Thanks for the replies to my misquote. It is a stepper motor.
And the whole cable was bad, which is why I couldn't find it.
ger21, thanks for making the light bulb go off, that was about the only...
I'm just setting this up. Everything seemed to be working fine. Until it wasn't.
When I jog either up or down, I don't know which direction the motor is going to turn.
This is a Nema 34 with 8...
Ummm...... I don’t want to come off as a jerk here, but I just looked those up. They are precision ground. A good precision ground ball screw costs about 10 times more than a rolled one.
I have never seen a C5 rolled ball screw. The only C5 I have ever seen was ground. Who is selling a C5 rolled ball screw? The C6 I use has a pitch tolerance of +/-.0012 over 12". Is this the one you...
Generally, the only reason a larger tool will last longer than a smaller tool is not enough RPM. In most cases, max spindle speed is just not enough to truly run a small diameter too fast enough....
I would start checking for cracks in the casting. I’ve seen it before. You can get hairline cracks that are really hard to notice.
I have a Sharp 2412 that I've had for 6 years. I'm not sure why you wouldn't want to buy ER32 collets because of the size. They aren't that big when it comes to a mill. They are more versatile for...
We sell conversion kits at heavymetalcnc.com. They are direct drive, and they come with everything included.
How are you linked to the machine right now? Most older machines use RS232.
I'll try this from memory, and hope it's the same control I'm thinking of.
After you put the memory card in the slot, push the program button.
That should bring up card on a soft key.
hit the soft...
We've got the new kit finished. It looks great. Ignore the wrinkled sheet. It's up for sale on our website. HEAVY METAL – CNC Conversion Kits for Table Top Mills
...
We have finally got the kit finished for the SX2.7/Little Machine Shop #5500.
Go to our website @ HEAVY METAL – CNC Conversion Kits for Table Top Mills...
No electronics, but everything else.
We just finished making a new kit for the SX2.7.
We will have it up for sale on our web site Monday or Tuesday at the latest.
Bruce
Hameavy Metal
HEAVY METAL – CNC Conversion Kits for Table Top...
I know you said no online stores, but online metals has whatever you are looking for at whatever length you want. Starting at 12" lengths. The aluminum prices are very reasonable.
I did some research on trying to buy a table top machine without the lead screws, handles, and everything else you will not be using.
I got completely shut down. The short answer is, they would...
I will second the Alu-power end mills. They work great, at a great price.
You will be looking for high helix high positive cutting edge with only 2-3 flutes.
They polish the carbide to keep the...
I've never put much trust in simulators.
I've always believed you won't truly know what is going to happen until you go out to the machine and run it.
Of course that just may be me.
On the last line you have, I use "X-136.5 Y-38.5 FMAX M99
I also don't understand the asterisk on the +0 for the dwell.
We have been working on designing a kit for the SX2.7.
I am doing this with the LMS 5500.
After tearing into it, I'm really liking the machine.
After converting an X3, I think I like this...