Search:

Problem solved a combination of gridshift and manually finding home position and reset parameter 1815.4 did the trick, took a while to find home position but all sorted now.

I Performed a reference return (ZRN) for the Y and Z axes, however the Z Axis ran all the way to the hard limit without decelerating
A little investigation into the problem showed I had a faulty...

Ok I got my PMC Ladder edited and I wan't to re upload however when I try I get the following error

"this function is protected"
I am loading via PCMCIA card.

I think this is because the...

Ok I have found the problem from the PMC Ladder BARALM is looking for an open state for an alarm and the barfeed is opposite ie NO normally open closed in alarm condition.

I don't have any...

Hi I have an ECOCA SJ-20 which I have integrated a Hydrafeed barfeeder to, after electrical connections power and relays were installed I enabled barfeed KEEP RELAY K5.3 but the machine will now not...

.

Hi mactec54,

Thanks for your reply my drive is a CIMR-VMS27P5 27P52 620409, I would need to price and re-installation procedure also.

I Have a F602 / F604 alarm this was intermittent but now occurs at start up all the time!

I understand that this is an input power alarm or phase out etc I have increased the supply power from...

Fanuc..!

Hi Guys,
We have a

Dainichi BX-35 with Fabuc 10TF with FAPT Control
YEAR 1986
Seriel number S7208-12

Turret is windmilling and wont stop, my technician has asked for:
...

with some experience on sliding head machines you can take quite a meaty cut but it all depends on material, so sppeds and feeds to suit are crucial, normally with a heavy cut the feed would be a...

Hi Guys, ive just purchased a Citizen E20 and what a beautifull bit of kit, the only problem i have is that the machine came with no programs in it and it has a LNS Magazine barfeed, now does any one...

Hi and thanks for the replys, i don't think these went to the States though there may be one or two of them over there, the answer to my question was yes....! a conversion kit costs £1000 UK Pounds...

Hi guys, I'm about to purchase a Citizen E20 (screw machine) made in 1990, now i no you can go to 32mm from an E25 but can you go to 25 or even 32mm with an E20 machine...? The machine is at auction...

Hi thanks for the reply, yes its a 9000 program and you execute it by calling up the G65 which reads the sub program, with this installed do i have to turn a parameter on so it reads the macro....?...

Hi guys, isn't this just the best forum on the planet..! Ok i have a Colchester Tornado 100 with Fanuc O/T Control, half keyboard and i'm after the Macro B program as i have an 8 inch hole to drill...

Hi guys, isn't this just the best forum on the planet..! Ok i have a Colchester Tornado 100 with Fanuc O/T Control, half keyboard and i'm after the Macro B program as i have an 8 inch hole to drill...

Hi guys, isn't this just the best forum on the planet..! Ok i have a Colchester Tornado 100 with Fanuc O/T Control, half keyboard and i'm after the Macro B program as i have an 8 inch hole to drill...

hi, it only says O-T , not c or a ...?

Hi, thanks for the reply, model control is O-T and its a half type keyboard, i have worked machines with this keyboard with all wear and writing..
cheers
gollame

Hi guys, i've posted this twice now and had no replys, i'm Desperate to get it sorted. I have a Colchester tornado 100 with OT Control, i don't have any wear offsets and i can't put tool headings in...

Hi i have a Colchester tornado 100 with OT Control, i don't have any wear offsets and i can't put tool headings in or any writing in the programme thow the machine will accept it when i download from...

Hi i have a Colchester tornado 100 with OT Control, i don't have any wear offsets and i can't put tool headings in or any writing thow the machine will accept it when i download from pc in brackets...

thanks for all your help...! ive fixed it, turned out to be a sticky door limit switch on the solenoid.

Hi, after having a similar problem maybe i can shed some light, there should be a parameter to turn the rs232 on and make it active as ours wasn't turned on.. hope this helps
gollame

Hi, we have an alarm error it reads "1000 spindle monitoring error 17" then straight after, we get on both axis the 401 servo alarm VRDY off error. Basically if the spindle goes over 50 rpm it cuts...

Thanks for all your help so far just one hurdle left to go :-|

I seem to have an initialization issue before I can load any parms I need to initilize the the system in the book under CHECK SYSTEM...

we learn by our mistakes, the hard way...! lol yes it was 2nd hand, if its the same lathe then i assume the same parameters...? ive typed in the name of the machine in google and theres a few...

Hi, abselect sent you our problem and yes you was right, its was the main power supply, ounce fitted all red led's were no more, the problem is now the machine crt only displays rom and ram checks...