Search:

The older 5020 you can use M64, not sure if it will also work with U10M.

I would probably just use swept toolpath rather than do the surfaces, you can create two lines at top of .5 rad, one on each side, extend them out about dia of your tool then joint them with 1.175...

Solid would be a better choice since you can go back and rechain using solid manager

To shade just press ALT+S and again to unshade

We have 3000m control and it only takes Conversational, meaning no G-Codes since it will not understand it. I use mastercam to generate the conversational using mastercam post.

3D is possible...

Here is the file, hope it is how you wanted it.

BIKRAMJEET_GILL2 -2.MCX

I moved in your rough pocket to leave only .062 so the 1/8 end mill can finish in one pass
I also changed your rough...

jamie1 I'm working on it, having a little problem with control definition but will try to get by.

I did saved it as older version of Mastercam

BIKRAMJEET_GILL2 .MCX

Not sure what you're trying to do, are you just trying to run A finish pass? What do you mean cutting through all edges of...

We have Mazak QT350-II with Matrix Nexus control that set up for one press to close chuck and press again to open. As far as which parameter to change I have not found that yet.

Okuma use Mode In/Mode Out.

Try a simple call

CALL Oxxx

Try changing "select color" in Configuration's System color page.

Mazak EIA is just like Fanuc Format. We have Nexus QT-350 no live tooling
and this code works for me
G83X0Z-1.550R.05Q.25F.005

We use M17 on ours.

On our Dynapath Delta 20

T0101 means call tool#1 and offset#1
T0100 will cancel offset on tool#1

T0210 means call tool#2 and offset#10

Take out the "B0"

You do not need to cancel the tap cycle after each hole, just give a new location ,If I remember correctly Q(value) can be added
to specify retract plane otherwise it will...

Lathe or Mill ?

Tell them to save the file as Version9 (.mc9).
X3 can save the file as older version, not sure about X2 though.

Do you have pallet changer on that machine?, that #1102 must be for checking pallet or table number. Can you post last few lines of sub Pxxxx.

You may have corrupted data in drive C, also check if data cable (IDE cable)is tight, try unplug and plug it back in and reboot.

Try these codes, this is similar to what g-codeguy has but with lead-in and out just in case you want to use nose comp later.

1/32 R Insert No Comp.

G0 X-.0625 Z.1
G1 Z0 Fxxx
G3 X1.968...

Yes bocko912 is right ..there are 3 sections on that Cavity Insert but I think they were part of design change or to make them interchangeable with similar part but with different Ribs.

Insert...

Yes..That was typical EDM finish surface. To get the sharp inside corners you would first machine A graphite block to match the shape of Cavity, it can be just one big piece of Electrode or you can...

I use WinPro DNC to transfer programs between OPS5000MG and A PC, the settings that works for me are..

Baudrate = 4800
Data Bit = 7
Parity = Even
Stop Bit = 1

On the sofware side:
Flow...

I have no problem send and recieve to Delta10 and 20, the last line in the program there was a word "END" , and I'm using Winpro DNC as communication program

Use "Window" when selecting contours

Just keep pressing the key and watch the characters change

To do system restore on XP just go to system tools dropdown menu, or click on RUN and copy this code... %SystemRoot%\system32\restore\rstrui.exe .... and paste in the RUN's window and hit Enter

Quick sample codes for you...

starting at 9 O'clock

(G41)G1X-1.0 Y0 F... (feed in to edge of circle)
G3 X-1.0 Y0 I1.0 J0 ( do full circle, X and Y end points can be left out)
(G40)G1...

I and J are the distance to center of the Arc in X and Y. Fanuc will read I and J as incremental distance.

So if you start your arc at 3 O'clock... "I" would be minus "J" would be 0(zero)

If...

Hi Mactec54

Anyone could see that capitalcrew is trying to learn how to write a program, If he wants program off the Cam system..many peoples in here would be happy to do one for him in no time.

capitalcrew ..Try this out if you still have problems getting ramp-spiral to work.

%
O04401 (part 44 side 1)
T1 M06 (LOAD ENDMILL)
G90 G54 (ABS OFFSET)
M03 S300 (SPINDLE ON 300 RPM)
G00...