Just a note: I had a private email exchange to Bill. I believe his intent was good and not intended to hurt after our conversation. I apologized to Bill for my misunderstanding and harsh response.
...
Type: Posts; User: DynaCNC
Just a note: I had a private email exchange to Bill. I believe his intent was good and not intended to hurt after our conversation. I apologized to Bill for my misunderstanding and harsh response.
...
Well I don't know who you are. I don't understand why anyone would bring up or start a post looking for problems. To answer your question: I answered your question as to why we do not see posts about...
We take care of our customers through our trouble ticket system, direct email, and by phone. We do not use this forum to fix customer problems or answer customers questions. From the time we...
Just give us a call on our tech support line. We are happy to help you get started. Or email me personally and i will help you.
Dave Cress
It sounds like you do not have the correct configuration in Mach3. Check the ports and pins for output #1. It should be: Port 2 Pin 1 to fire the torch. If I remember correctly the plug was cut off...
So glad someone could help you.
The truth will set you free... and this ain't the truth.
word Bill...word.
Your so very welcome!
Sure Bill: You can download the configuration files right off of our web site for FREE! They are the same ones that over 500 other DynaCNC machine users are using without problems on the same type of...
So please inform me in detail how you put a low target voltage "trying to fool it" on the control system? I can't understand your comments and how it affects the control system unless you define your...
I don't know which machine you have. Why not email me directly and I think I can help you with this.
Dave Cress
DynaCNC
Just simply download the drivers from our web site for FREE. They have been there for 3 years for FREE. Our trouble ticket system on our web site has been there for two years and you could simply...
DynaCNC / Dynamic Plastic, Inc. does not subscribe to doing business on the CNCZONE or any other Internet forum. We do not slander, embarrass, harass, free advertise, or discuss issues or problems on...
DynaCNC / Dynamic Plastic, Inc. does not subscribe to doing business on the CNCZONE or any other Internet forum. We do not slander, embarrass, harass, free advertise, or discuss issues or problems on...
The post processor is located on the setup disk provided with every machine. If you can not find it please give us a call we aill be happy to provide it to you.
James, I ran your g-code on my machine here at the shop. The jagged arcs are about the same on our machine as they are shown on your photos. I looked at your g-code generated from vectors from your...
Mr. Bill Bright, ( lowpull )
Below this paragraph is a copy of the email sent to you on Yahoo on the CandCNCSupport forum.
To answer your above comments: 3-4 week turn around time is an...
Thank you for your productive comments; To answer your above remarks:
1) We have an option that contains the lead screw on both ends of the "X" axis. It was added a month ago to our fully...
Mr. Watts,
Sorry to lose you as a prospective customer.
Sincerely: Good luck with whatever you do decide to purchase.
I apologize you are offended by the correspondence, however I did state...
Turboboy,
I am not sure who you are. I really can't believe we treated you that way. I will look into this, however you have not identified yourself. I really feel it is a cheap shot not talking...
fasttimes,
I am not really sure who you are. I am a bit suprised by this. I am not sure why this problem is a problem. We are always ready to help our customers.
Just an FYI: Tom (as pointed...
We can help
Tell it like it is. Most everyone knows the truth, and most everyone knows the lies. Do the math and count the conplaints on every side. I know most everyone that has a CNC table reguardless of what...
Dynamic Plastic, Inc. EXPO Training Seminar
May 19th & 20th
Mach3, SheetCAM, Hypertherm Plasma Torch, Artistic Cutting, Toolpath generation, DynaCNC & Yamaha Robotics Demo.
Download the agenda...