Setting up dyn2 drives to a cnc drives axbb-e motion controller. The dyn2 manual states pin 11 is a disable pin with 5v applied. I received a wiring diagram to an axbb-e controller board and it...
Type: Posts; User: HCE
Setting up dyn2 drives to a cnc drives axbb-e motion controller. The dyn2 manual states pin 11 is a disable pin with 5v applied. I received a wiring diagram to an axbb-e controller board and it...
Anyone with a Rutex r2010, r2020, r2030 be able to read the markings on the tantalum capacitor, mine have seen better days. See attached picture.
I have a router with desk cnc. Have not used it in a long time though.
A pulse generator to send a signal to the stepper driver, limit switches, industrial door opener switch and some relays. No need for an audrino. How big of a stepper motor is needed to replace a...
Looking for spare rutex drives prefer r2010, possibly r2020. Also a r2120 breakout board.
Great attitudes can't, can't, can't.
Same attitudes I see with printed face masks when the machinist community gets involved. Not FDA approved, won't pass fit test....
Seems like a group a fools...
Have you presented this question to Dart?
After using Stuarts frame I look at the G0704 and wonder if the z axis is not rigid enough. To take advantage of the frame one really needs a good spindle motor and strong axis drives and motors.
Have you tried the drives with a tuning cable directly from the parallel port, bypassing the break out board?
Have you read through the smoothstepper documentation. It looks pretty straight forward and step by step. https://warp9td.com/index.php/gettingstarted/setting-up-the-smoothstepper-and-mach
The...
Maybe I am reading the instructions wrong or theses are old instructions, but I understand 500 to be gear number.
Electronic Gearing ( GEAR_NUM Parameter )
Gear number (Gear_Num) is set from...
Seems there are a few that have started with the step and direction option, kind of get working, and end up using the analog input route via a pwm to analog convertor.
2000 steps per rev is the...
I'm still in the going to get to it stage. My concern is the high minimum step count, combined with the high speed of the spindle and no ess. Dmm said that they could write firmware to lower step...
Are you sure you do not have 12mm x.8 threads, pitch and diameter are nearly identical.
Not everything. Yes the pin hole has to be parallel to the main bearing shafts, and the center line distance from pin hole to main bearing shafts has to be accurate. But the clocking of the crank...
How much increase in stroke?
I assume you are using a mill?
I would think only the flywheel side would have to be accurate radially as ignition timing would be affected, and even then depends on...
Deepgroove1 has spindle motor setup. Consew makes a brushless servo motor for controller that are all over ebay. I have been using a treadmill motor with a kb controller running with the taig step...
You would have to remove the desk cnc controller and replace with a breakout board to get Mach 3 to function. IMService supports deskcnc IMService.
Can you give us some more information on this motor, or possibly a link.
Glasgow
Where about in MT.
Is there a general rule for chip thickness (feed per tooth) when trochoidal milling. The only information I found was to increase it 3.5 times over conventional milling.
2006 yz250. no f.
Zomvgtek
What are you running for stepper and drivers to obtain that speed?
Try this
Not sure why I did not tell you to do this in the first place, but send a email to clarken at [email protected] <[email protected]>. Most importantly post back with his reply. We need to get as...
I am not sure how this would work. you can save different profiles on the desk cnc board and reload them under machine setup, but you would also need to make a different deskcnc program on the...
What did you get for a lathe?
Are you attempting to use the same controller or getting another desk cnc controller for the lathe?
Well I kept having trouble till I pulled back my max velocity to to 65000 sps. This helped tremendously on consistency. If my machine is warm, clean, and smooth it will handle 84000, but it does...