Just bumping this thread as I'm keen to get this project going again, any idea of some software I could use for this other than the mach?
Cheers
Type: Posts; User: Jonathon
Just bumping this thread as I'm keen to get this project going again, any idea of some software I could use for this other than the mach?
Cheers
Hi Guys,
It's been a while since I visited CNC-Zone, Its definatlye grown.
Ok I have been playing with Mach3 formular trying to get a http://hektor.ch/ style Two motor hanging painter to work. I...
Will do, Just got to convert to DXF's.
Yeah the one i copied is a variant of the one you have measured, it doesnt have the hinge, maybe I should incorperate this as it would make the side parts...
Hey Benny,
Got a mate with one of those sims, I too have been keen to cut some out omy router so I spent some time yesterday drawing one up ,although not yet finished will be soon.
Only problem is...
poppyplant,
I too have a Compulathe and CompuMill The Mill I am retro fitting with new Gecko Drives but the lathe is still intact. I have all of the manuals also.
Which parameters do you mean?
Jon.
I use PICAXE chips, They are Michrochip processors with a picaxe bootstrap very easy to program easy user interface good support and they are cheap.
www.picaxe.co.uk
Not totally on topic but while on a robot course for work I discovered these, very alien like flexipicker robots made by ABB. Very cool video on their page.
IRB parrallel robots
You sound Happy! I know the feeling. Good to see that my problems have helped others.
Yeah thats right, Like they say, "The answer is always in the last place you look." THE INSTRUCTION MANUAL !!
I didn't reduce the current, and so the motors were cogging.
But if it had have worked...
DaveP.
Here is a bit of a diagram. Fisrt i wired them in series, then I combined two coils together on each phase so halving the steppers resistance. So they are wired in parallel, as colors go,...
The stepper motors im using have 4 windings, 2 windings per phase (8 wires), the phase windings were wired in series first for high torque, But this was causing the motors to resonate at 500 hertz....
FIXED!!!
I wired my motors in parallel and it fixed the problem.
Thanks for the ideas guys.
Jonathon.
Ok, so I got home keen to try all these ideas and I decided to take the motor off the screw and there you go it still does it. On all drives on every LPT output and with every motor, it still...
The drives have Full Step , Half Step and Quarter Step , they are set on 800 steps.
They have only one shaft, I have tried different feed rates but because the motor still has to slow right down when doing an arc it still does it, I thought I might change it from direct drive to a...
Hi Fella's
Iv'e just completed the build stage of my router, Its dimensions are 1500 X 1500 using wiscarver linear bearings and 5mm pitch ball screws. I'm using RTA HGD Drives at 50v 6 amps, 3.5Nm...
After looking for a simple circuit,wich there doesn't seem to be, I think you might be right Pete.
Thanks for the reply.
Hey,
I have made the mistake of not checking the encoders on my servo's before oredering 3 gecko drives. (chair)
The encoders are Harowe Servo 11-brc-300-G.
Is there any simple circuit to convert...
That was a quick reply, Its 1:16AM here.
I have sent emails to them and they offered to fit a new controller for a huge sum of money, I'm using a null modem cable and hyper terminal at the moment...
Hey everyone, This is my first of many post's, just found the site.
Anyway,
I have two Hercus machines with "ANCA 2000"controllers, one is a Compulathe and the other a Compumill. I have the...