Search:

I need a few parts cut and etched from veneer, some with 3m adhesive backing. if you are capable of doing this and have access to veneer for cutting email me for files and drawings to quote.
Thanks...

I need a few small pieces in aluminum and stainless. some milled, some turned, and some are multiple opp. if interested and capable of doing small watch sized parts please email me for drawings...

Please email me if you can do cnc router parts in bamboo and hardwoods, and if you are capable of doing a six sided machined part (square but requires six different setups).
also have some simpler...

Alright guys,
I have all the parts spec'd for my large router using the belt drive described here, but I cant seem to track down a good source for the pullies. I need the T5 32mm wide pully for the...

With so many options out there I need some help. I am building a 4x8 gantry router out of 80/20 and pbc integral v-bearings for limited production use. There are so many controllers out there that...

Will be running cincinatti cnc mill and lathe. They have acramatic controlls. hours and pay are negotiable. Contact me on the supplied email below.

Louie
[email protected]

We have a cincinatti mill and lathe with acramatic controls. We would like someone part time, maybe two or three days a week to run the machines for us.
contact louie
310-490-6344

the holes and perimeter are the important part. you can use standard 3/8 sheet and leave the survaces unfinished

most metal houses carry 1018/1020 steel standard. you can quote for 4130 if you would like.

I can supply material if you are local to 90755, otherwise quote job cost and material cost. I get it for about $9 a foot

sorry. stock size is 4x3.5
quote and i will get you a better drawing if needed

tollerance for slip fit. if anything -.001

you could use 1.25" stock and just machine the length and innher taper on this one. inner taper would be nice at +- .001

+-.001

there are three pieces that I need turned out of 4130 stock. we get each piece for about $11 each. we need eight of each piece.

Thanks
Louie
[email protected]
562-595-5410

I need ten pieces of the supplied drawing. I currently get them for $10 a piece in that quantity. can you beat it?

Thanks
Louie
[email protected]
562-595-5410

three seperate pieces need quoting. short runs of 10 pieces each. we are currently getting each piece for $4. can you beat it?
Thanks
Louie
[email protected]
562-595-5410

When i jog my tree journeyman 425 at rapid pace i get error faults that stop the machine. the most common are
x axis runaway
x axis overtravel

the machine is not close to the limit switches,...

anyone?

Where can i find information on which post processor to use for my tree journeyman if i am using the catia machining package?

flames for a cnc plasma cutter?

thanks for the input. After tracing wires for a while I found that they simply used the fifth wire(white) for a neutral on another 110V circuit that they wired on the machine. That leaves me with...

I figured out that the white wire was for a neutral for another circuit. now I just need to figure out why they used an orange wire as one of the hot wires. It is a pre assembled wire bundle so...

I recently recieved my tree journeyman 425 and was baffled at the setup instructions. It states that i can only run 230V, and that if i have anything else I need to run a transformer and also switch...

Ok, the new mill states that it must have 230V three phase power. is this true, and if I have 240 what should I do. There is also a five wire plug that the machine was attached to, what is with...

I need to have my journeyman hooked up, and was thinking of doing it myself. would you recomend this, and what precausions should i take?

So I just recieved my first cnc mill. It is a tree journeyman 425 that uses cat 40 tooling. as I have only used the manual R8 collets before I am totally in the dark. Where do I find used tool...

well I had an idea for a really bad ass tubing notcher, like the ones sold by mittler bro. I would get an old motor, slide tables, and a milling vice, and rig up a table to hold it all together. I...

i am having a machine moved from MN to CA, it is a tree journeyman 425
who have you used to load and ship machines before. I want the good and the bad. tell it all.

I need some parts machined. It will be only a few pieces at first but the quantities will increase if the prototypes work. please email me to see the files. I work in catia V14 so if i can send...