I have a Niigata HN80C with a Fanuc 15M controller. It appears the feedrate override switch is disabled in the controller. The controller is seeing the switch change and the binary numbers are...
Type: Posts; User: ktmrider
I have a Niigata HN80C with a Fanuc 15M controller. It appears the feedrate override switch is disabled in the controller. The controller is seeing the switch change and the binary numbers are...
My drives only have one pot.
I am trying to use some Advanced Motion Control B25A20AC drives with a +/- 10 V input signal on a 3 axis mill. I am looking for advise on which mode to operate them in as well any hook up tips. ...
System 10 mostly. Its all stock from the drives out. I know the Mach 3 is not sending a signal to move. Something common to all three axis is off.
The contoller is Mach 3 via a KFlop/KAnalog. The contoller is not sending anything to the N360s. Where they used to sit still now makes them take off and buzz around. I wonder if one leg of my phase...
A previously well behaved mill is now wigging out. When I turn the power on the servos start moving. Something common to all 3 axis is causing them to just move uncontrollably. Any suggestions what...
Thanks for the advise.
I need a replacement encoder : Dynamics Research Corp 152-121-500-18SR. Does anybody have any advice where to find one?
JPA - thanks again for the help. Do you have a chart or something you are referring to?
Wonder how I get the machine to stop looking for something in the tape drive?
Thanks JPA. Got that fixed.
Does naybody know what "Error 11 - T-Out" means?
Thanks for all the info!
What did of transformer should I be looking for? I am an HVAC guy so traditional transformers are all I know. I don't know anything about a toroidal.
I am a newbie and I need help building/finding a power supply capable of 80 to 90 VDC and upto 20 amps. I looked around on here and found a couple of tidbits on the subject, but I am still not...
Now I have an ERROR 3 - Grid Error
I finally got my Tree 330 powered up and it has some issues.
When I first power it up I get a ROM ERROR and then it goes away to:
ERROR 07
IIC Centurion IV
Version 66.45+
I think there is...
Thanks for the info all.
I finally got my Tree 330 powered up and it has some issues.
When I first power it up I get a ROM ERROR and then it goes away to:
ERROR 07
IIC Centurion IV
Version 66.45+
I think there is...
My Tree 330 has a N360 Three Phase Half Wave Controller made by Gould Gettys mounted on it. What does it do?
Another cabinet also has a Kleanline Electronic Filtering System. Any idea what it...
Thanks for the code help P!
The machine is actually a Journeyman 330. I was mistaken earlier. Does anybody have the electrical prints for a 330?
I found this on the web at:
http://www.tools-n-gizmos.com/specs/Tapers.html
NMTB (Quick Change) Shank
ANSI B5.18, National Machine Tool Builders' Association, 1927. DIN 2080 / IS 2340, ISO...
I am wrong again. It's a quick change 40 taper, not a 30.
Does anybody know if reagular 40 taper tooling can be altered to quick change tooling. I recently got a machine with a quick change 40 taper spindle. I have a full set of regular 40 taper stuff but...
Great! I send you a PM. Thanks.
I recently got a mill with a quick change 30 taper (Erickson) spindle. My question is the manual locking collar robust enough to hold tools accurately? Do anybody have any experiece with this type...
Thanks for all the suggestions. I had no idea there where so many choices.
I'll check out DeskCNC too. Thanks.
Hey thanks for the help.
Ok I found the KFlop info.
What is the dspmc?
Hey that Kipware milling program looks pretty neat. Thanks for sharing.