Hi; could someone please point me to a place were I can download the instructions to build these boards and the parts list?
Thank you
Mariano
- - - Updated - - -
Hi; could someone please...
Type: Posts; User: rasta
Hi; could someone please point me to a place were I can download the instructions to build these boards and the parts list?
Thank you
Mariano
- - - Updated - - -
Hi; could someone please...
hi Uli;
are the files for these servo drives still available?
regards
rasta
hi;
in the he link on Ali express only specify 1000 mm as the longest ball screw that can be supplied, these are to small for a bridgeport machine
regards
Mariano
thank you Tom , as always you can't have better service than the one at Dynomotion.
regards
Rasta
Hi Tom ,
Thank you for your reply
Would please advise the method of connection , with a PNP and NPN?
Would it very hard to implement the PNP solution?
Thank you
Mariano
Hi Tom, thanks for the reply
The reason why I like to switch the positive side , of the optho is that the machine generates
A lot of electrical noise , and in my limited knowledge I figured that...
Hi Tom, thank you for your prompt reply
The mechanical switch is wired as N.C.
The optical sensor is a NPN , but if needed otherwise I can buy the PNP ones
The ground side of the switches power...
Hi; I want to use 2 limit switches , on the same axis side on my machine , I want one switch to be mechanical , and the other optical ,
I want to mount the mechanical in the machine table while the...
Hi Alex , what is the price now?
ok; let me point out something that I have learn over my years as a cnc operator and programmer, closed loop servo refers to a motor with a device that keep track of the position of the shaft of such...
[QUOTE=agray;2331146]lowering price....
100.00 each
175.00 for a combo (1 KFlop and 1 Kanalog)
300.00 for all four boards.
Price does not include shipping or paypal fees.[/QUOTE...
Thank you Tom, looks like that the next few months are going to be a busy ones, meanwhile if I got the U and V axis going , I will edit the post output, not very elegant way , but that is all my...
Hi Tom;
does it means that KMotionCNC will interpret a command like G00 U20.V10. and those axis will move? and the readout of B and C will show the movement ?
regards
Mariano
Hi tom;
perhaps I have not expressed myself properly;
what I need to have is a total of 6 axis in the readout , X,Y,Z,A,U,V , And I need readouts for all of them , in U and V case because they...
Hi Tom; thank you for the prompt answer
The standard axis naming for wire edm is XYZUV , and if I change that I will have to change the axis definition in the cam package$$.
at the moment kmotion...
Hi Tom;
Im developing a 6 axis wire edm , and will like to change the DRO LABELS to XYZAUV , can it be done? if so please guide me...
thanks
Mariano
hi;
this thread is about 8 years old , are there any new developments?
thank you
Rasta
Hi; does anyone wants to sell a kanalog board?
Hi;
I want to buy a Kflop +Kanalog boards
are there any sellers?
Mariano
Hi; Did anyone made any inroads on this project?
Regards
Mariano
hi;
have you been able to modify those dries to take step & dir?
regards
Mariano
Hi;
great work!
if you surface grind or machine the face of the worm holding block, at an angle of say 1 degree relative to the axis of the worm, the backlash can be made adjustable , by sliding...
I also have problems when I use mastercam in a wide screen laptop, when setting the stock , the OK tick is below the screen view
as most laptop manufacturers today ship their units with wide...
Thank you, thats what Im looking for
regards
Mariano
Hola;
me llamo Mariano , y tambien tengo un par de Yaskawa como el suyo, y me gustaria si es posible
saber como ha conseguido conectar sus controladores , en interfaz con Mach3
gracias
Mariano
el problema es que los parametros son diferentes incluso entre maquinas de la misma marca y el mismo modelo, ten cuidado..
Thanks Kevin, your prompt answer is very much appreciated
I like the amount of I/O in the cards, the 8010 is a 16 bit isa/stand alone card, the 1200 is an stand alone one, someone suggested that those cards understand gcode
, well , I have been...
I have two cards , the ACR 1200, and the ACR 8010, they both come from an old controller given to me.
Thank you , for the prompt reply, that Acroloop card was given to me some time ago, and looks like a good controller, any idea how much is the mill software?
Regards
Mariano