Any link to good tutorials is appreciated ????
Type: Posts; User: SharpShooterSer
Any link to good tutorials is appreciated ????
Got it running finally. Small sensor was off its spot and that caused the problem.
Now to the hard part lol. To learn how to work on it.
Anyone have the idea where am I supposed to to put oil for...
Hi
I recently purchased this machine. First problem is that the machine is in French. Second problem, for me to start it up I have to press in two relays in the back. Third, once the machine starts...
My 220P is converted to run on LinuxCNC, and at the moment I am using puller to get the stock material out.
I tried using G96 and CSS for getting optimum finish and good cutting/parting, but after...
I recently got my hands on one of these babies with T1 controll. Thank you Marko for all excellent videos on YouTube, and thats awesome work on restoring it. This is my 4th Emco (V10P, 5 PC CNC and...
Video of it in the works :)
https://youtu.be/fpyERpAHT2k
Thanks to Andy from linuxcnc forum, its sorted out (except fine tuning pwm, that still has to be tinkered with)! Attached is proper configuration. Spindle not turning with M3/4 command -...
also, my threading cycle isnt working. I get the readout on the spindle speed, but the tool advances to the start point and just sits there.
edit - complete folder with custom hal file is included...
It seems I need some more help to get the spindle working through VFD.
Now, my spindle speeds up to full speed slowly, and I wanted to insert spindle-at-speed option into HAL. I followed the...
It works :) just to let others that try to do something similar. Now to see how to properly configure .hal so it works with interrupter too, and to set the scale properly so the actual rpm is the...
Thanks a million John! I ll report back did it work!
It seems that I first have to resolve the wiring of the 5axis bob and SPINx1 board, then to move on to wiring the SPINx1 to Sinamics VFD.
Most of the output pins are free, but what to wire where?...
Went ahead and replaced the spindle and bearings - old one is looking bad (and stock bearings are literally fried...)
Now, I will wire up the VFD, SPINx1 card and new motor to the BOB. Question...
thank you very much, I will modify it (and to check other ngc files) to see will it help!
I am sorry but I cant tell you that. If no one here with experience in this type of controllers chims in with advice that is certain, I would advise you to visit yahoo emco f1 group, there will be...
I am not certain what type of the motor is running the main spindle on your VMC mill, so my experience isnt that useful. I connected the spindle motor (DC one, standard on F1 mills) to the ...
thanks, I will try that!
played with it a bit more today. rezeroed everything etc, and run a program part by part (except part 1 of the program). it seems that somehow my part offsets were wrong, because now I have a...
it does, and then dro numbers change and it all goes south (-z direction)
thank you for pointing that to me Gerry, luckily my program didnt get to that part (last chamfer pass) or there would be more mess to look out for.
I am measuring tools the simplest way I saw, tool...
I got my mill all set up an working, with spindle motor control with 0-10V analogue output, and I am still getting familiar with third axis :) other problems arises though - I have to get limit...
I am new with running Mach3 and cnc mill as well (I got used to emc2 and 2 axis lathe). I am still learning and trying to figure out the offsets, axes etc, so please be gentle :)
I got a code for...
and bit more detailed hardware pictures. did I miss to connect/wire something, or theres something wrong with the mach3 setup?
software setup
I am retrofitting my cnc mill, and finally I have everything wired up (I hope), but I need some help for configuration for spindle control.
I run a 0.44 kw DC motor (stock) that is powered with...
Small update, for anyone trying to do the same or similar - the motor speed controller/power source is easy to wire with the existing F1 DC motor - it works with nothing special to it. Still have to...
As promised, a drawings for tapered gib mod
Hi
I was just wondering can you fellas help me out? I have a gcode generated by Solid for a part I am working on (and it has a fanuc post-processor, its not my Solid 2015 copy, and I cant mess with...
I had my F1 for almost two years, and I havent used it at all. Its in working condition, with old steppers and old control box, but I am making a modern control box, and retrofitting it all (the...
you can also check http://www.cnczone.com/forums/benchtop-machines/308372-software.html
you will need cheap BOB, 2 stepper motors, 2 stepper drivers and power supply, some wires and you are good...