You would just need a dissecant air dryer ,,, nothing fancy.
Type: Posts; User: Frosted Images
You would just need a dissecant air dryer ,,, nothing fancy.
What are your requirements? What would you like to do with this cnc router?
Has anyone ordered the Tongyou ZBW-160E 5.5Kw vacuum pumps? I would like to know an exact confirmation on the amperage they pull on 3 Phase? I could not find any specific information on there...
I have a Blue Elephant 1318-4 that's with a 4th axis rotary. Keep in mind that these machines are built to your specifications. The more you know how you want your machine to perform, the better...
It would that any compressor with 90 or more psi should be compatible. Therefore, a compressor of 120/240v single phase would work.
I'm in Jacksonville FL and I own a Blue Elephant 1318-4 4th axis rotary. I love my machine and I run it from any software.
Can I receive the wiring diagram for my pneumatic alignment pins on my Blue Elephant 1318-4? Obviously, mines doesn't work and appears not to have been connected to the switch.
I wouldn't have dared to attempt running Mach 4 on a Chinese CNC. I have a Blue Elephant 1318-4 with Mach3 and the XHC controller. I was skeptical about even running a usb controller period. The...
I have an HQD spindle 4.5kw and so far I have had no issues or no stalls. I'm cutting walnut, mahogany, oak, .50" acrylic and etc. I choose to go that route rather than the HSD or water cooled...
Tom Zhang
I have sent a deposit on 6/27/17 and haven't seen any verification of my 1318-4 Blue Elephant being built. Who was yur agent?
I just placed an order for 1318 with 4th axis rotary on June 27th and still waiting on some confirmation of being built. I dealt with Tom Zhang
I am looking to purchase the Maverick but legacy couldn't ell me any info about the motors or controllers...cutting speed and rapid speeds. Then they charge $2500 for a water cooled Chinese spindle...
Just acquired a Multicam 48 Plus. The dang machine runs on serial port and came with Windows 98 with Enroute 3. I need a manual for the Multicam controller? Can I output directly from Vectric Aspire...
Can you give a little insight why Yihai sucks? What model of CNC did you purchase? Which features did you receive with your purchase? Are you running Offline or DSP controller with Mach 3 (LPT port)?...
The Mogul is very accurate. You will not find a better machine for the cost. I run a 36"X48"with a Craftsman Digital 2 1/4 hp router. The good thing about the Mogul is that it is an open source CNC....
I have an Epilog Legend 36EXT. My laser started doing the samething December 28th. I have replaced the motherboard 5 times since owning the machine since October 2010. I just replaced my encoder...
Wow! That is pretty promising. I cost me $2800 to have my laser recharged but it will last 5+ years depending on how hard I run it. That is the key to laser operation, knowing how to minimize your...
No. You may can find a used Chinese laser in that price range but typically not. Expect to pay between $3500 or more depending on your requirements, table size, power wattage, and rotary attachment.
The forum having issues uploaded my post. So if it shows double post of the samething I am not double posting a reply.
At the time that I was importing these machines, RECI tubes wasn't available....
And that is the thing. You shouldn't have to worry about whether your tube is losing power just by sitting on the shelf. I was for sure that I could truly benefit from my glass tube laser. However, I...
And that is the thing. You shouldn't have to worry about whether your tube is losing power just by sitting on the shelf. I was for sure that I could truly benefit from my glass tube laser. However, I...
I truly believe that the life of the tube is the day of manufacturing. I owned a G. Weike LG3040 40W laser and went through two tubes in 3 months. I truly believe these glass tubes were used to test...
I owned a G. Weike LG3040 40w. I went through two tubes in 3 months. As stated before, you dont know if you are getting a test tube in your laser or a new tube. Laser can not sit without use for a...
I owned a G. Weike LG3040 40w. I went through two tubes in 3 months. As stated before, you dont if you are getting a test tube in your laser or a new tube. Laser can not sit without use for a period...