I'm looking to see if I can verify the parameter settings.
The unit in the cabinet with the red LED is the power input module. Manual trouble shooting schematic says if control does not power up the...
Type: Posts; User: hmc710
I'm looking to see if I can verify the parameter settings.
The unit in the cabinet with the red LED is the power input module. Manual trouble shooting schematic says if control does not power up the...
I opened the parameters pages and there was data there, right or wrong, i dont know, but not just zeros.
Battery alarm light was not on.
The control is lx1
I have one board, the power input unit, that has a red led, all others including dc power are green. Checked for other estops, no chip conveyor, snd looking for an oil pressure...
Hey all,
Working on a similar issue. Just powered up an old mori sl-4 with yasnic ls1 control. Powered on the mains and then the control and get a 310 servo power error and control interlock on, but...
I'm going to see if one of the old towers I've got laying around will come back to life and try it again....Seems strange that two fairly capable people couldn't load it up....
Thanks islander,
I've been looking at both options and starting to dig into the old control to verify what's what. I've tried to load two computers with Linux in the past with zero success...... a...
Hey All,
Been away for awhile and back to looking at upgrading my two Dynapath machines. In over simplified terms, the two controls, a 10 and a 20, no longer boot up so I would hope there would be a...
Yep, program wasn't loaded. That will teach me to be gone for 4yrs....
Good news is using G91 and subroutines is saving time and space!
Well, screwed the pooch on this one..... I just went ahead and did a sub routine. Went to test it and while on the program page decided to clean out an old program to free up some space. Opened up...
I've got an old Acroloc and I am machining a contour. I need to repeat this 6 spots and do a perimeter cut 1" deep in aluminum with a 3/8" mill. I could write a sub routine, but I can also use M99...
Thanks Angelw!
I've been on the road so long and not in front of that machine I couldn't have done it from memory.....
H
Thanks!
Anyone know where I can find a KD7A mother board for a Jet Edge water jet. They say it is no longer available so we need to upgrade. Did a search and can't seem to locate one or find out what...
Nick straightened me out on 708 / 709 parameters - they are in inches. Will go through proc again staying in the Inch mode.
Thanks for all the help on this!
H
Working on the zero return set up on Tornado 200
Do I need to switch my readout to mm from inch to work with apples to apples? I did switch to mm and when I did the z position turned negative.
My...
Thanks Nick, hope you had a good trip.
H
Hey All,
I've sent PM to 600 Service and Nick1945 but I don't know if they have gone through or not? Can either of you help with my APC310 parameter procedure?
Thanks,
H
Changed all the D cell batteries in the panel door (once I found them)
looking at resetting the parameters for the 310 and 320 codes. Seeing how this is called a Zero return, don't I have to put the...
I just read through the maintenance manual and the troubleshooting section and I see a reference on the schematics for batteries but nothing in the manual with battery part numbers. I'm also kinda...
I've been working on the road a lot and have kept the power locked out on my 200 Tornado to keep accidents from happening to it. I turned it on today and got the 310 reference and low battery alarms....
Thank you Dan. Will check these out. I appreciate the detailed reply!
H
We started to get an intermittant SV013 V-Ready Off error when we are running a common program. It usuall faults when we move to the unload position and M00 to stop the program and wait for part...
Check voltage on dc power supply today on the Delta 10 machine with the dead crt.
T1 +5.12 vdc 0vac
T3-5 0v (ground)
T6 28.1 vdc .38vac
T7 -14.84 vdc 0vac
T8 +15 vdc 0vac
T9 & 10 115v input
...
Opened cabinet on the dead screen machine and have 3 red LED's on the control boards. I did notice that the resistor on the large capacitor was missing. You can see where it has been scorched and...
There are also the typical Horz Vert Contrast control pots inside the cabinet if the above method does not work.
We have two old machines and run good when they run. One acts like the keyboard is dead, and the other we turned on today and the screen does not come on. Any suggestions?
Thanks,
H
Thank you Sowen, will give it a try. Right now I can generate the code then use the Find / Replace to get is close.
Thanks,
H
Running a mill with Delta 10 control and trying to get Bobcad Post processor Delta Event to generate the nc code the way the machine needs. I've tried to open the post with a number of different...
I've only seen the turret go one direction. Shock absorbers? Will check into the lube. My turret has drilled balls where the coolant comes out. PIA to adjust or control. PM sent.
H
Good luck with that, I'm hoping I won't have to do that anytime soon. Got tailstock aligned and cut true for a few pcs then got some taper back. Changed out my cutting insert and will try another...