Search:

Maybe you are looking for SYSREAD ID503 NR(Preset-No.) IDX1/2/3 ?

A few more information about yourself would help:
what controller and what version of it have you got?
Is the Preset table...

SYSREAD ID220 NR2 IDX1/2/3


Regards

cgTNC

I don’t know a suitable machine function for a mechanic sensing device.


Solution:
Touch two points, note down the position, calculate the angle with the calculator and set the corresponding...

With the Heidenhain-iTNC 530 I solved it roughly like that:
"In %34inverted comma%34" engraved: In "inverted comma ".

If the %- character is used in the string, then the following 3 numbers are...

Program the desired target position in cycle 421

After processing the cycle, the current value are displayed in X and Y.
In Q153 the diameter

Regards
cgTNC

If you are not able to program Q366, then I guess your controller’s version is older than the manual!

Regards
cgTNC

You first have to copy the program with the program manager of the demo into a folder that is not on the TNC e.g. on a USB stick or in C:
Afterwards you can copy it onto the controller without...

I had the same problem 2 weeks ago.
I was editing a program graphic and I change a block and scrolled down without waiting.. and suddenly the program ended in the middle... sauer.gif

Exactly as...

Simply download and install the demo programming station from Heidenhain and try it out. All options there are activated.
Regards

Is the backup only from the TNC folder or of the PLC?
In the PLC you can find a folder which is called kinematics or a similar name...
You have to play it in with the TNC Remo in the demo version....

I guess it’s a colour screen- then I would say it’s the screen.
What machine have you got?
Maybe it has a standard VGA- connection where you can connect a normal “commercial ” screen-

Regards...

There are several possibilities;
-calculate it as you mentioned
-measure the radius at the desired position on the tool pre-set device. (if available)
- drive to the desired depths and „scratch“...

Its possibly works better if the WAIT FOR SYNC is not written in the repetition, but before it.
There are also differences between the programmer station and the machine
On the programming station...

Do you mean:
L M140 MB FMAX
With that, the milling head relieves until the end of the transport area in tool direction, also when the processing plane is swivelled.

Sometimes that command can...

To avoid that the translation with cycle 7 is gone after a M30, you can write to a label:

LBL 100
PLANE STAY RESET
ZERO POINT X0 Y0 Z0
PLANE SPATIAL SPA0 SPB0 SPC + Q..
ZERO POINT IX + Q.. IY...

1. Measure as you described and calculate angle with ATAN,
2.With PLANE SPATIAL SPA0 SPB0 SPC + Q.. (Possibly with TABLE RED) Align the C-axis,
3.Now the zero point should still be fit enough to...

Look in the current programming space, there is a lot splashing around.
This can be copied to the machine.
With the Fixture wizard in the programming space, the dimensions of the templates can be...

Just a question: The part did not shift?
The turning axes stayed where they were supposed to stay?
What do you mean by “milling kind +1”?

Regards

No, simply LBL 99 as our last block in the subprogram.
Regards

You write about a neutral point table.
On our iTNC530 from DMG, the PRESET table was active right from the beginning.
I can open it with the soft key PRESET in the manual mode.

Maybe you have...

You are right! thumbs-up.gif
On the left side of R1 you can see a point of the dotted point.

Regards
cgTNC

For the 6mm groove underneath 15 degree, the location is missing. If it isn’t shown then you can only ask.

Regards
cgTNC

I have not worked for ages on this controller.

As far as I can recall it, the editing the macros is similar to the N *- sentences: Usually you need to use a key combination to switch in the...

It is well known that the simulation is very slow especially by pivoting and big tool diameter. So nothing helps really.
Perhaps you can display the item as small as possible with the Zoom softkey....

Look in TNC:\BLUM\TOOLSETTING.H.

Gruß
cgTNC

I don’t know the Impra insert nuts.
We only turned Ensat insert nuts so far. For them, there is a special insertion tool.
In the left-hand motion, the locking loosens without assistance due to the...

Are you kidding? How are we supposed to know where you jump to? coangry.gif
But that should explain your program:

E81 = E19 (infeed.) (E81=5)
E82 = E18 (Max depth) (E82=-70)
E83 = E81 - E82...

Hello Teem
Well if it’s only about the simulation

Either switch off the collision control in the simulation or position the work piece in the working space over MOD.

I don’t know what the...

Hello omnia
I can only guess that you might want to change the M92 position?!coangry.gif

With DMG machines press MOD in the editor, then the soft key ‘user parameter’.
You can change the M92...

Hello ricoh77,
When pressing enter, the contour calculator creates fixed G1/G2 and G3 command. So it needs constant values.
As an alternative you can use modal edge rounding, if I remember...