Search:

I tried that this morning and it seemed to work. i loaded the program i wanted to cut and ran 3 cycles, about 45 minutes with no problem. It wouldn't run a minute before. I sent a different op...

Hi, my fadal is down again and i really can't figure this one out. I was changing programs and when i hit enter after typing the program number the screen froze up. I couldn't get to any pages and...

I am still in desparate need for a fadal tech. i found someone last time on google and had to pay them to learn about my machine, pretty much got raped. I need a tech that knows fadal. please...

Hi, i have been working on the orientation problem with my machine and see that there is no signal to the control from the orientation sensor. i adjusted up to 20 and still nothing. I think it...

I still need a repair person in concord, the fadal keep breaking on me. I found someone last time, but I had to pay him to learn about my machine. I am looking for an expert, please help.

hi, my fadal is broken again. seems like all i do is work on this machine and now i am just to busy and need professional help. I have spent hours on google, calling other machine shops, and can't...

I'm looking for a PDF of the maintanance guide for my 1994 Haas VF-0. I cant seem to find it anywere. thanks in advance.

just installed the new servo and its working. Now a new problem, the cold start isn't lining up with the marks like it used to and I'm afraid it will throw off all my G10s I spent hours setting. ...

I hope so, I'm really behind on production now. When the machine first went down I could still jog the y and z axis, but it would fault out when I tried the x, now the machine just faults out right...

just got it apart and the x axis servo was seized up. I hope it didn't take out the amp card also. time to order some parts.

I checked the x ball screw and it looks like the table isn't getting lubed. it was pretty sticky. I got it lubed and moving, but the machine just keeps going into emergency stop mode after 1.5...

when the machined stopped running it sounded like it hit a hard stop, but it was in the middle of the table. I have hit the hard stop by accident before and the sound was exactly the same.

I am getting to the point were I need a pro to come check this problem out. i lost a day and half of production already and still have no clue what is causing the motor overload fault.

I hear ya, when it comes to electrical I am pretty much lost. And when I read schematics, they seem to never match what I am looking at physically, like when the manual says "white Button" and they...

yes, but it doesn't really help me find the physical part looking at a bunch of lines on paper. I can see were it should be in the circuit, but no clue were they hid it in the machine. I really...

i still cant find it :(

Hi, my x axis suddenly shows a motor overload fault, I have been digging through the manual, searching google, searched this forum and keep coming across a motor overload relay reset "white" button. ...

Hello, I am new to fadal and I am setting up 8 parts. I use a haas normaly and my code has g110, g111 for fixture 7 and 8. it doesn't seem to work in fadal, and I cant find any info on google or...

I am having the same problems, it started when I put windows 7 on my computer. new files and old files. someone help us, LOL. I don't want to put xp back on my computer. My new computer is also...

Well, I called haas and they stepped me through some diagnostics and come to the conclusion that the Regen Resistor is bad. It read 20 ohms at the spindle drive and should only read 15. The bad...

Thanks for the responce. It makes sence to me, but how can I diagnose and fix the problem?

Hi, I am new to the board and need help bad. I have a 1994 Haas VF0 and today the spindle drive fault is keeping me from cutting metal. The spindle comes on and runs fine at all speeds, but then...