Search:

I have 3 - vexta model # pk564ana-tg30 stepping motors 5-phase, .024/step, DC 1.4A, 0.7ohm, 30:1 gear box mounted on them, 5 wire lead + black, red,orange,blue and green. I cant find any info on...

I have 3-Vexta 5-phase stepping motors model# pk564ana-tg30 DC 1.4a
0.7ohm .024/step 5 wire leads, 30:1 gear box installed on them......I cant seem to find any info on them. Can these be...

I was finally able to get my machine up and running. The question I have is once Ive completed the drawing in Autocad what version should I save it as so that I can run it thru a g-code converter. ...

Iam trying to cut some balsa ribs for a plane project. I am was wondering if anyone could suggest the type of bit I could use on my porter cable mounted router..Iam usin a 1/4" collet. I have pre...

If I have drawn a 2" x 2" square and I am using an 1/8" bit for cutting do I need to allow for the 1/8 offset from the bit . Jim Stidham

I have drawn something in autocad 2000, it measure out to 12" x 4" , I saved it in in a dxf. format autocad version 12, sent the file into cncpro for g-gode conversion. Everything seems good to that...

If anybody is using Supercam software to run their CNC router please let me know your thoughts ,,Jim

I have a computer that has a AMD Athlon 1000 MHZ processor, 384 megs of ram and 80 gig hardrive ....It is running on Windows ME .which one of the softwares will work , master5, mach1 or mach2...

I finally am at the point where I can start cutting some balsa parts for rc planes. I have approx. 18 years of experience with cad and I have used compufoil and profi for airfoils. I am interested...

Is there anyone that can help me with setting up turbo cnc so that I can finally get this machine up and running. I have installed it on my computer and am in the set-up & configuration area of the...

the metal box was picked up at the local Home Depot, cost was I believe $21.00 it is about 6" deep & 12" wide has several 1/2" to 2" electrical knockout holes. As a matter of fact the knockout hole...

I ve attached a photo of my power supply box, Ive installed the 24v power supply, 6.5 amp fuse, power cord, 24v cooling fan, 3-axis xylotex board, cables supplied by xylotex for my stepper motors. ...

I am finishing the hook-ups for my 3-axis xylotex board, have the 12v - 6amp power supply hooked up, fan , fuse and switch all done. I need to get a 5v power supply, is this something I could get at...

I finally have my machine together with motors mounted, Ive purchased a 3-axis xylotex board, fan, power supply and all the wires from the board to the motors. Does anyone have a schematic or...

I have gathered the following parts
machine
Xylotex 3-axis board
cooling fan
3- 116 oz nema 23 stepper motors
24 volt power supply
computer and software

Is there any website that gives any...

This question is for Balsaman or anyone else that can shine the light on this subject- What part of the system creates the speed is it the controller, the type of software used, how much power or is...

another view

attached a few more picts - different angles

I purchased this small cnc router set-up in the picture below. Can any one help me with the right type of motors and controllers. It has a 12" Y-axis / 12" X-axis and 3.5" Z-axis. I will be using...

I am in the process of bidding on an small all aluminuim cnc router set up on e-bay. The travel is approx 22inch for the x-axis and 17 inches for the y-axis. I will be using the dremel router on...

I am new to the forum and starting on my first CNC build. Does anyone know a good place to purchase the 8020 alum 40mm x 80mm size...thanks Jim:cool: