Found the issue. Swapped monitors and it's working fine. Bad Display. Thanks
Type: Posts; User: Bryan Rogers
Found the issue. Swapped monitors and it's working fine. Bad Display. Thanks
I have an EZ TRAK DX and when i go to the Utility screen it come up really wierd. Its all white starting from the middle of the screen and all I see is the very top of the utility screen text. That...
We have a Makino A77 Horz w pallet changer and shuttle system
We want to convert to a stand alone system and get rid of everything in front of the machine including shuttle,rails, loading station...
Does anyone know the actual Bearing numbers for a J series Head? Looking for the top cap bearing, and the bearing under the adjuster plate for the variable speed.
I don't need the spindle bearings....
Thanks
Does Anyone know what the bearing numbers are for the spindle in a VS50 with a 12,000 rpm spindle with through the tool coolant?
DMG Mori needs part numbers and they have to check with Japan for...
Have a Delta 2000 on a DeVlieg boring mill. X axis won't jog with jog keys. Swapped X and Y
Plugs at the servo trans board and now I can jog X with the Y jog buttons. But can not jog Y with X...
I'll look at the tool clamp/unclamp Diag tomorrow. Thanks
No alarms or messages. There is a tool in the spindle now and we can turn it on in MDI. X and Y axis will home and move. You can index tool mag also. I think it might be related to the ATC and...
Working on an old HC 500 with pallet changer. Fanuc 10M control. The Z axis will not move with toggle or hand wheel. NO alarms. Had a spindle alarm and shut down and rebooted control and now this....
I'll check it out. It used to work fine until the memory board crapped out and I had to reload all the parameters. It homes and the spindle runs and orients fine. Just the tool drum is acting...
That's what it was. Had it repaired along with the Braking Unit . Thanks
Have A Chevalier Lathe that the Braking Resistors are getting super hot and smoking right after you turn on Machine,, You don't have to run the spindle.
Could there be a problem in the VFD braking...
Working on A Kia V45 Vertical that I had to reload the Parameters in. Has a Fanuc 0m-c control. Everything seems to work ok except the tool change cycle.
The 20 tool drum will index to the correct...
Could be your AxisBob card and or limit switches. You can check limits in diagnostics to see if they're changing. I had an EZ trak that showed the limit for X stuck on but it wasn't. (Home Switch)...
Working on A Kia V45 Vertical that I had to reload the Parameters in. Has a Fanuc 0m-c control. Everything seems to work ok except the tool change cycle.
The 20 tool drum will index to the correct...
Thanks for your help. LeBlond sells parts for these lathes but due to some legal issues between them and the current builder I have to contact Racer Machine in Canada for the specs if they have...
It's a VF A.C. motor
Model V 2601-BN29
Kollmorgen. 10hp 6000rpm
I recently bought a Standard-Modern lathe from the 90's. Excellent condition with Vickers (Siemens) A2100 control. It has Kollmorgen drives but is missing the spindle drive.
Got it for a song but...
I have a Clausing surface grinder that I can't get the hyd. motor, coolant motor or wheel motor to come on. The contactors are ok and when you push them in manually everything works.
When you press...
Have an HT20SII with LX3 control. After you power up machine in back and hit the NC on button the screen comes up to Multi screen and after hitting the Operation soft key you hit the Standby button...
Thanks
I'll try this. We ran it all night on Tuesday and no problems so far. When it would stop and hold at 120 deg the motor would whine but not fault.We'll try to adj. the parameter
I have an HA5C4 indexer with 4 rotary indexers. We are getting a hi load alarm which means according to the manual a software fuse. The control has been looked at by Haas and they say it is fine....
Haven't tried this yet. The machine is about 2 hrs away from me. I think the owner has scheduled Yaskawa out of Columbus Ohio to look at the problem.
Thanks for your input
Bryan
Thanks. I'll try this to see what happens
Bryan
I'll check the motor but I know its a Fanuc. Just don't know the specs
. Thanks
Problem with boot up. When machine is powered on the screen gets to Handshake 1 and stops. We re-seated the cards in the rack and now the screen has no text. The backlight is on but no text.
I...
We are looking for Electrical prints and manuals for a KIA KT20 w/ a Fanuc O-M control. Need to diagnose some problems but have no books.
The spindle will run in high and low but when you give it a...
Have a Chevalier grinder and when you press cycle start in manual nothing comes on. I checked all fuses and voltages and they're all good. Could there be a problem with the I/O board?? When you...
I have a problem when the stop button is pressed to stop the spindle. The reversing contactor should kick in for a second and slow/stop the spindle. Same for spindle reverse, the forward contactor...