The max you'd be able to use is really a 5" chuck. With a 6" chuck, you could spin it, but it wouldn't allow you to open the jaws much wider than the chuck OD, since that would hit the way covers.
...
Type: Posts; User: DSpeck
The max you'd be able to use is really a 5" chuck. With a 6" chuck, you could spin it, but it wouldn't allow you to open the jaws much wider than the chuck OD, since that would hit the way covers.
...
Don't give up on the machine just yet - it's a very nice piece of kit. I have two, one complete with original control, and 1 with no control on it.
Mine both came with no tailstock - very custom...
You could also do a similar thing with a servo on the spindle, replacing the standard motor. Then you could run the spindle as a spindle, or position it for drilling. Might need a brake as well, for...
I finally found the right circular connector (turns out you have to buy the insert and the back housing separately - Digikey US), and with some fiddling around, got it installed and the other end...
Thank you, Intelitek!! I'll order the connectors and build a cable for testing. I'll post back here after I build and test the cable.
Thanks for the link, Iron-Man. It's a few years old, but they may be able to help.
The turret on this one is driven by a stepper motor, not a DC motor, so 4 of the wires should be no problem to...
If you go to this link, the download is zipped, but unzips into 2 floppy-sized folders, which you can copy onto diskettes so you can reload it. It turns out I have the original software on 2...
The cable I need is the one that controls the turret. It goes from the back of the machine housing to the control box. The lathe end has an 8-pin round connector, and the control box has a 9-pin...
Still looking for this info. Can anyone help me out with this?
Thanks!
I have recently purchased a turret for my Prolight 3000 lathe. It didn't originally come with one, so I don't have the cable to connect it to the control box. The turret is from a parted-out...
If you can find one, an old Emco Maier F1 CNC mill uses BT30 tooling for it's quick-change spindle. You could salvage one off that, but maybe not that cheap. These were good quality Austrian made...
Use STP Superclean. It actually dissolves the caked-on oil. I have used it to clean numerous machines, and it works really well. I have even managed to get stuff removed with it that wouldn't respond...
If you can find one in the UK, get a Prolight 3000. If possible, make sure you get the original control box and computer (or at least the control card from inside it - proprietary and required). I...
We've been doing a bunch of stuff at work with bearings, lately. From this experience, I can tell you that the option 2 is your better choice. Also, your bearings should be a tight fit on the moving...
I have a couple of DV-59s around that age, that I plan to do the same with. I wish you luck and good success withthis. I will definitely follow your progress with interest!
Have you begun...
According to Centroid, you do need to run 1:1 on the spindle vs. encoder. They suggest a minimum of 2000 lines/rev (8000 cpt with quadrature).
I have several lathe projects in the future, and...
Yuo could look at Hardinge CHNC III or IV's. These meet nearly all your requirements, if you get them with 16C collets. They tend to have 7.5HP spindle motors, but may have had options for 5 HP. They...
Unless you are really looking for the challenge of building your own spindle (I can respect that!), you may be well ahead for your build to buy an older Hardinge small lathe (a DV-59 variant, for...
You'll find the blocks aren't all that cheap, so be prepared for the extra cost.
Unless you go with a router, you are not going to find a spindle worth the bother for <$200. When you get into...
GRBL is something I plan to use on a couple of my machines. I have bought the Arduino packages I mentioned above, so I'll see how they work. In your case, if your stepper drives still work and take...
For your first foray into CNC, you might be better off going the very inexpensive route, and setting up a GRBL system.The motors could possibly be reused, as they were strong enough originally,...
I usually hand-write the program. Hand-writing lathe code is a lot easier than mill code. I've used Mastercam at work, for some parts there. There are a few free lathe CAM programs around, for basic...
You could try Hoss's method of using a belt drive and tucking the motor back under the table. This would be the shortest mounting solution, and seems pretty straightforward to do...
I bought a Prolight 3000 last year. It had come from a school, and I got it intact and working, original computer and all. I have used it several times since, and I can just say - use it the way it...
Here is the location for downloads: Intelitekdownloads.com
The spindle already has an index wheel, and an encoder wheel (100/rev, if it's like mine). You can re-use the spindle encoder stuff. It's optical, no need for prox. You can use a C3 board(from...
Steg, can you post a picture of the location on the lathe? There seems to have been a number of variations of the H105. I will have a look at mine to check if I can see what you mean. Also, earlier...
It's been several months, and I haven't seen anything more on these in the Zone - anyone have any reviews on theirs yet?
Interesting build - don't see many people here making surface grinders! Best of luck with your build. :)
I hope you have made provision to cover your rails thoroughly - grit getting on them will...
No, he meant Torcam. They apparently did, among other things, updates of high school shops' CNC machines. I bought a benchtop CNC lathe (Meccanica Cortini H105) that had been updated to run from a...