Where can I find someone very good in solidworks that can build me a model of this bezel? I'm in fresno ca
Type: Posts; User: Ezra
Where can I find someone very good in solidworks that can build me a model of this bezel? I'm in fresno ca
Guys, Thank You a lot! Im going to have the piece cast by a foundry that does antique reporduction and then have the lettering engraved. I will be back here for help with the engraving at a later...
I would like to repoduce this bezel in a quantity of approx 25 pcs. it is approx 7 inches wide. The reporduction needs to be identical to the original. Material : aluminun.
How much would this...
***SOLD***
Thank you all for helping me. You have all been very kind. I wish you the best of luck with your projects.
Guys,
Im getting a number of emails saying "I'm interested in your machine but first I have a few questions".
Can you please research Joe's homepage about the machine, cncrouterparts.com about...
i will ship but it will add $100 for peanuts, boxes and time to disassemble. plus the cost to ship it to you.
BUMP
$350 for the machine.
Everything $850 (the cncrouterparts.com 3 step kit alone cost $600)
559-349-0513
I will sell my Joes 2006 for $400 and drop the price every week or so until it is sold. This is just for the assembled kit. Come by if interested and I can run a program and show...
Fresno,Ca.
559-349-0513
About 5 months old.
If your interested, call me and come by and we will have the machine run through a program so you can see it working.
What I have in it so...
My Yaxis slopes downward approx .125" when moved from one end to the next.
What can I do?
I run Mach3, is there a way to have the software subtract this amount as it moves?
I thought about...
Guys,
If i used the T-Channel available from 80/20 inc. to create linear bearings,
will that stop the sagging in the Y and X axis
Guys,
In the middle of my Y axis Im sagging approx 1 mm. Basically destroying my thin carving.
Are there any kits out there that I can buy to adapt my Joes 2006 X and Y axis.
I saw the...
Hi Guys,
Is there a touch sensor that I can put between my bit and the Corian Im carving in too. Ive been using a feeler gauge and have been going back-n-forth as I lower the Z-axis, somewhat...
High Density Polyethylene (HDPE) Sheeting | U.S. Plastic Corp.
I hate finding some answeres after I post a question.
Hello Everyone,
Im looking for a source to build my Joes 2006 Skin out of HDPE.
Any leads?
Thank You
I drew/cut a straight line with my pen connected to my machine. I was supposed to be 127mm. When measured it is really approx 162mm.
Do I need to adjust a ratio somewhere within Mach3?
...
Do I put double nuts on both ends of the lead screws or just the end opposite side of the motor?
I have it all assembled and ready to go.
Firen it up tommorow:D
Guys,
Whats the purpose of a backlash screw and plate?
reduce vibration?
keep the main bolt from popping out of the plate when direction is changed?
Hi Guys,
Any advice on what paint to use to waterproof the MDF?
I'm going to paint it green and call it The Green Macheen
I used a mitre saw, angle grinder with a cutoff wheel, 1/16 drill bit, 5/16 drillbit, 5/16 drill bit with point(the ones for wood), safety glasses, thick finishing nail(instead of center punch).
...
I took a tape measure and my four long pipes should be 59 5/8". But when I watched the video about modifications , the guy says 60 inches. I just wanna make sure, any advice.
I took a micrometer...
OK, Thanks Dorsal
Ive done a dry fit of all the pieces last night. This kit is really strong on its own.
the two 36" gas pipes - what diameter are they?
the four 1" gas pipes - what length are they?
i searched "gas" and "gas pipes" so i did my homework and couldnt find the answer unless i...
Guys,
Whats the best way you have found to cut the notch for the bearing slides?
Thank You
Did you gentlemen begin gluing from the get go or did you do a dry build first, disassemble, and then glue everything together?
Im planning on using simple Elmers Wood Glue, if anyone has any...
Nego_o,
How easy is it for a novice to learn/work with Mach3?
My Joes2006 has just arrived and I have my computer and just paid for myMach3.
3 axis kit on Nov19:D and we should be in...
Hi Torchhead,
Ok, so am I correct when I say I need to next purchase a PCI video card?
When I install it, will the Dell's internal video card be automatically turned off?
Do you have a good...
Guys,
I was looking at a 3 axis kit and controller for $510. Its worth every penny but Im trying to get my Joes 2006 up and running on a shoe string and just wondering if there is a less...
Torchhead,
for some reason i cant send PM's on here so i will say it publicly...........thanks for your post, i did buy the above mentioned computer and just finished installing windows...
Torchhead,
Thank you!!! I looked at that auction. Do you see anything with that auction that would contradict with the :
Mach3 Minimum Requirements:
32-bit version of Windows 2000, Windows...