Hi Derek,
" I'll post my results when I (Balazs) get it dialed in and maybe the settings will be a good starting point for someone with a similar setup
Thanks again "
Any further progress with...
Type: Posts; User: Tig
Hi Derek,
" I'll post my results when I (Balazs) get it dialed in and maybe the settings will be a good starting point for someone with a similar setup
Thanks again "
Any further progress with...
Al,
the printed material is always helpful.
The commutator is scored, but not to badly. I would chuck the motor if it wasn't for the nice brake on it.
Vger,
The motor diameter is 3" and...
Hi Vger,
Yes it did. The encoder was a Sumtak M# 0105-0421 600p/r.
I am trying to salvage the motor because of the working 24V brake which just happens to fit an 8:1 gearhead I had laying around....
Mike,
Perhaps I was not specific enough.
The picture posted was the original picture from the ebay auction. There were no such information plaque (nametags) on the motor that I received.
Hence:...
Thanks Al.
Anyone else familiar with this motor?
Hi guys,
I wonder if any one out there can identify this motor I bought on ebay.
Yes, I know there is a plaque in the photo, but that's not the motor I received.
The seller stated that "the...
Hi,
It's been a few years, but last time I checked, You could purchase these
"Input Hub Sleeves" from Danaher Motion for about $25.00 each.
They can be reached at: 1-540-633-3400
Hope this helps.
Hi SuperBob,
If you don't mind me prying, are you building a stretch former for metal?
Count me in if you can produce a drive that will actually supply 200V at 20A continuous, and at least 50A intermittent.
A dumping circuit would be nice, so it won't fry, when the inevitable crash...
DSL PWR:
Re:
I think if you look around a bit you will find that almost any 7-10hp compressor will output 20cfm. My little Dewalt portable outputs 3.8cfm - 100psi at 2.7hp. Used it cost me...
Dennis,
check out Esabs Air Curtain (water muffler) P/N 22018
Go to the ESAB web site and Plug: F-15-189-B into the search window to retrieve the article.
This device mounts onto the business end...
eloid,
Sorry for the delayed response. As stated by Vacpress, It is very much machine specific. If you give the sales and support people the specifics of your proposed machine, such as a realistic...
eloid,
Check out ATLANTA Drive Systems
http://www.atlantadrives.com/racks.htm?gclid=CK_ereWny48CFRVlYQodOEJHog
They are World Leader in Rack & Pinion Drive Technologies specializing in precision...
Hi, How are the bigger 250V 40A Vipers coming along. How will they compare with the Rutex R2020.
Thanks.
I wasn't for an instant thinking he would just give it away. As stated earlier by Splint and Svenakela, it might be a good opportunity for someone to pick up the slack.
Time marches on, and in a...
Hi, Any word yet if someone else will betaking over production of the R2020 drives.
Thanks,
Tig
Thanks Al,
With regard to switching the AC to the PS, I was concerned that the large bank of caps. in the linear PS would keep the motors turning long enough to do some real damage. I do have some...
Hi, would anyone know of a reasonably priced power relay, suitable for switching 200VDC @ 30A. I want an E-Stop switch that will kill the power to the R2020 drive with certainty. I don't like the...
Thanks Haydn,
I will look forward to it.
Hi, Regarding Flexible Cable, just how many strands are required in a 14 AWG conductor to be considered for "Continuous Flex" ?
Also I am seeing AC specifications stating: "Shielding suitable for...
Thanks I will check them out tomorrow.
Hi, does anyone know of any suppliers in Canada, for Shielded Flexible Servo Power Cable.
Thanks
Tim
Hi,
Another question regarding inrush current suppression.
I was just wondering: if one was to stick the Inrush Current Limiter on the primary side of a 220V:120V, 3KVA Industrial Control...
Hi Haydn,
Great looking PS. I just ordered a couple of NTC surge limiters for a PS I am assembling. Could you elaborate a little more on your relay setup. Is the switch integral to the relay, and...
Thanks Al,
I think I will play it safe, and change the adapter flange on the gear, and not screw around with the bearings.:(
Hi,
does anyone out there have any experience changing the face mounting flange on a DC servo motor.
I have a couple of SEM MT30 servos that have NEMA-56 mounting flanges that I would like to...
Thanks Tel,
I assumed it was a given, that if one was able to take on the task of retrofitting the tables, that fitting a couple of parallel spacing blocks to get the desired Z high would be a no...
Speaking of Gerber tables,
has anyone looked at the these for conversion: Lot of 3 Gerber Drafting Plotter Tables 20' x 8' two of them: Model 79s are presently set up with camera heads for...
Hi Jerry,
Check out Clayburn Industries Ltd.
Clayburn Refractories Ltd.
They have an outlet in Ontario. Phone: (905) 892-8861
Their head office is:
33765 Pine Street
Abbotsford, BC Canada V2S...
Hi Jerry,
If you are thinking about waterjeting, You might want to take a look at the WJTA (The WaterJet Technology Association) web site: http://www.wjta.org/. This is a valuable resource, and well...