Greetings,
Join the LinuxCNC Forum and search for similar conversions.
LinuxCNC
The support from users is rather good.
Cheers,
Type: Posts; User: fc60
Greetings,
Join the LinuxCNC Forum and search for similar conversions.
LinuxCNC
The support from users is rather good.
Cheers,
Greetings,
Rather than trusting my poor memory, read up on G18 and G19 codes. One is for XZ moves and the other for YZ moves.
G17 is, generally, the default machining plane (XY).
Remember to...
Greetings,
Check the configuration of your software looking for a "backlash compensation" field.
My mill has play in the ball screws and once I typed in the actual backlash value into the...
Greetings,
What is a "PDB"?
Where are you located?
Cheers,
Dave
Greetings,
Watch eBay for a good used Ames Portable Hardness tester.
https://amesportablehardnesstesters.com/
Make sure all the parts are present.
Especially the 62 HRC calibration disk.
Greetings,
My CNC mill is not very rigid. As a result, I take lots of "finishing cuts". Fortunately, my machine repeats well and going over the same tool path is not a problem.
I would suggest...
Greetings,
McMaster-Carr...
https://www.mcmaster.com/products/way-oil/trade-name~vactra-no-2/
Cheers,
Dave
Greetings,
This reminds me of MasterCam. You can configure the post/machine such that A0 is pointing at the Y axis (3 o'clock position as you look at the face of the A axis) or A0 pointing at the...
Greetings,
Is ProLight still in business? If yes, would you please post a link. I was unable to find anything other than the User Manual.
Cheers,
Dave
Greetings,
To remove the arbor, hold the large diameter flange (with the two flats) with a wrench and turn the inner shaft with a 12mm wrench until the arbor "pops" loose. Then unscrew it with...
Greetings,
I have the similar machine, a Smithy CNC1240, which is very close, if not the same, as the NovaKon NM200.
Mine works well, repeats well, and has been a blessing in my shop.
I...
Greetings,
Your solution brings a FlashBack to me.
Years ago I had a flatbed plotter that used a "Null" Modem cable.
I bought a box of connectors and a crimp tool to make my own cables.
...
@ArcticCynda,
"Export Regulations"?
Where are you located?
Cheers,
Dave
Greetings,
The McMaster spanner has a range of 16-20mm diameter.
Thus far, it is the closest fit.
Unless you can source a spanner specifically made for 18mm.
Cheers,
Greetings,
What is the diameter of the nut with the slots?
Here is a link to a hook spanner that may fit.
https://www.mcmaster.com/6975A12/
Cheers,
Greetings,
I have a Smithy CNC1240, similar to some of the older Novacon NM-200 machine.
My Z Gas Spring failed and I was able to order a replacement from McMaster-Carr.
...
Greetings,
The Spec Sheet says "Inverter Rating --- Not Compatible".
Cheers,
Dave
Greetings,
Does the bar have any identification on it? This will quickly determine the correct insert.
Cheers,
Dave
Greetings,
We used to machine hollow tubes.
To curtail the vibration, we would wrap a piece of surgical tubing around the part to dampen the harmonics.
Cheers,
Dave
Greetings,
I had a similar issue with my three phase mill motor.
Turns out the forward/reverse switch was dirty.
Fortunately, the motor repair shop did not charge me to test the motor.
...
Greetings,
For a Left Hand thread, do you not need a Left Hand tool holder and a 16EL AG60 Insert?
Cheers,
Dave
Greetings,
I thread mill with a Widia Carbide Threading bar. Just look up the min bore size in the catalog.
https://www.widia.com/us/en/products/fam.ccmi.100007813.html
Yes, it takes a few...
Greetings,
Google is your friend.
Search "1.7 kw to HP"
I get 2.3 HP, at the higher rpm.
Cheers,
Greetings,
I wrote to the seller asking for a PDF of the Owner's Manual.
Reply was...
"
Hi
Thanks for your message .
Sorry , the item do not come with user manual .
I have an early edition and find it most useful.
...
Greetings,
Please post again once you source new bearings.
Also eager to see what else is involved in replacing them. i.e. seals, torque settings, etc...
Curious to know the price you get.
...
Greetings,
I would set vice one to G54.
Then, move over and set vice two to G55.
Cheers,
Dave
Greetings,
I Googled Carmex Inserts as I use them in the shop.
Within the WebPage is an online thread calculator
.Carmex Tool Wizard - Welcome
It allows several Controllers for the Post...
Greetings,
I have a 12x40 CNC mill that uses a Toroidal transformer. It powers all 4-axes. X,Y, and Z are NEMA 42 motors connected directly to the lead screws. The A-axis is a NEMA 32 motor and it...
Greetings,
My CNC had a similar problem.
I run LinuxCNC with Stepper motors.
Withing the LinuxCNC configuration is a parameter to compensate for backlash on each of the drives.
Roughly an...