Danny,
The cd,9 has to be set the same as the software
used to load the control.
The book goes over settings and they have to match the
software settings.
I use
Type: Posts; User: kappullen
Danny,
The cd,9 has to be set the same as the software
used to load the control.
The book goes over settings and they have to match the
software settings.
I use
I use a fadal post but you have to call the program
a xxxxx.FNC file instead of xxxxx.NC.
I believe most basic Fanuc posts will work
and the VM 10 recognizes the FNC
tag only.
Good Luck,
Kap
Thanks for your help.
I have the access code for the
diagnostics page for anyone who needs it.
The memory dump procedure omits one step that I have
also.
In the parameters this machine...
I'm going thru a fatal memory error procedure again and when it gets to diagnostics step it says user not allowed or something like that.
Anyone have the code to get in Diagnostics on a TRM?
...
Thanks for your help.
These Hurco's seem to have several ways to skin a cat.
I went to the page listing tools in the pockets and inserted the
tool I wanted to change to auto to a slot with a zero...
I am operating a Hurco vmc that the tools are changing from "auto"
to "manual" (must be hand loaded). Winmax control.
I can't find the right page to change them back to auto load.
The training guy...
My Fadal TRM has only six hours on it!:D
Oh yea, I had to go through that SETP parameter routine last week.
I assume that action zero'd everything out.
The VMC 15, I didn't have time to...
Darabee,
You're right the power supply is fried.
Some little component on the back burnt clean off.
Have a new one ordered to be in Friday.
I'm buying it local thru the Fadal Dealership ...
That's what I'm thinking. Later I searched around on the site and found some
similar situations.
It's taking power in at 250 volts on the right and the meter shows nothing
on the other side...
Last week I had to go thru the dump and reload parameters routine
after a "memory error".
It ran OK all day Saturday.
This evening on start up in the cold start cycle something tripped
and I...
Have you looked at the counterweight chains?
I had similar issues and the some hardened bushings
over the chain link pins were busted off.
Bang every time a bad bush crossed the sprocket
on top...
Thank You Glove Box and others.
That dia comp screen comes up behind the extra
length comp screen.
It did the trick.
I'm doing 4-40 thread milling in A286 and couldn't hold size
without you.
Kap
We have a "new" Hurco from another department with
very few hours.
Everything else is tied up so I decided to give it a try.
I've tried all day to get the cutter comp G41 to work with no success....
Neal,
I am talking about generating a program in Mastercam, not in the Fadal control it's self.
I've made many a ball mold this way.
Kap
Jay,
You can create a segment of the arc required in xz, or yz, and rotate the arc
around the centerline to create a spherical surface.
Then surface the surface.
Kap
I learned to jog to cold start position,
and going thru the cold start procedure
before shutting down for the day.
I suspect there is another issue at work here.
kap
Thanks for the replies.
I'll let you guys know what we find out.
Kap
We have a Haas VF3 that has begun to drop tools from time to time during a tool change.
Changes seem a bit more noisy than before.
They are dropping while reloading in the magazine.
Anyone had...
THX,
I've had the same problem for some time.
After another near miss over the weekend, I poked around in mastercam 9
and found this;
In the left hand vertical menu bar, go into setup.
...
fm,
Sounds like the limits were set-up wrong.
If the limit is set to go off after the machine hits the spring stops,
She tries to go where you told her.
She sat there all that time under...
I am training on a Mazak Nexus-250-II Quick Turn.
I have a threaded (ID) part and need to adjust the threading, and boring tool,
back off so the bars don't crash into the back side of the bore.
...
Can you set up diagonally (corner to corner) across the table?
Kap
We needed a flexible, quick to set up machine for prototyping
repair, and short run production work.
Is this machine it?
By the time you discribe every tool, chuck jaw,
live center etc, you...
Dsuds,
I don't use the PA command but get the edit menu
at the bottom of the page by pressing the space bar.
Then all the edit functions come up.
c-change i-insert del-delete copy, replace,...
I had this problem with my new TRM.
The factory rep told me to remove, and re-seat the boards.
This machine bounced it's way across the country on a truck, and spent five months in a container...
Thanks for the reference Bob. You can find our e-bay store or visit our website which has just been added to the CNCZone links under Machinery, Tooling & On-line Stores. For your convenience you...