Search:

I am going to reset the boards tomorrow, no chaffing no chips. up until I took the power supply out and had it rebuilt the machine worked it just faulted on Rapid home. The machine has been run on...

I spoke with Dyanpath today they had me check the capacitor for teh proper bus voltage. He thinks it may be a lag issue however I rewired the machine to the Disco and now it wont go past the innitail...

Been a long time since I stopped in here, I have a Hurco Hawk 5D 3 axis mill with dynapath 10 control. I replaced the power supply when I bought the machine and it worked flawlesly for about 14 yrs....

Yep that was me sending the tip.. what I found on my PP gantry using mach 3 30% was way to high for THC %. Other people had me chasing my tail for ghosts. Once I talked to Ron about my loose gear...

Thank you, I do see inherit problems with this style of a machine, Racking is a big issue in my opinion the dual motor for a single axis is BS and needs to be mechanicly linked, and of course the...

Need to make some axle brackets for a friend.. So I played with the file, cut speed, peirce height and cut height. Here is what I got...Profile 20 IPM, ID 15 IPM pierce height .180 cut height .085.....

OOps I opened up a can of worms... Well, I have had my table up and running now for awhile. I did use the Backing Soda. And HAD 0 RUST.. the PROBLEM is that the baking soda drys out of the water...

My Drawing,PDF and cut part.. MAchine is running Awsome...

http://i10.photobucket.com/albums/a102/rockfab/SuzukSGusset2.jpg
...

I recieved 5 with mine also unfortunetly they were all normaly open.. great for home. limits are usualy closed.. They can be made to work.

Here you go... I am a machinist so I have some of he toys to do this. I also used a 36.5" ground rod instead of a parallel. So my accuracy is over 36.5"

For those using Dragon cut. you will use...

Go here and in my build I have all the wiring Diagram with Pictures on the Cutmaster series hook ups.

http://www.cnczone.com/forums/precision_plasma/110827-new_precision_plasma_build_3x4.html

The build looks good, I like your offset switch mounts LOL.. If you have not looked yet and want to get your motor tuning real good there is a you tube video that makes it realy easy and you cant get...

Right hand side low, just keep in mind the cover sits back it is not flush. So if you drill to far forward the cover will interfere with the hole you drill. Hope that makes sence.. I have not updated...

A little more updating.. the machine is up and cutting great, I have had a few issues to overcome.. and here is what I have found.
1) the large pulleys for the reduction were loose causing some...

Yep almost there... I can not say enough good things about the gantry kit I got from Ron at Precision Plasma.. Also the CandCNC Dragon cut has been as described, I just need to get a few little...

Did you set your Torch offset in Sheetcam post... Not that farmiliar with sheetcam just yet so I dont know much about the layer thing. My work around was to seperate posts.. heheh

Well the machine is alive and cutting.. I have been playing with some 14 material I had laying around.. I figure start with what I have and get the cut conditions perfect.. As of a couple days ago it...

sounds like a backlash issue seen in older knee mills when the screws start to wear out.

Same thing happens, with PRO. I feel your pain. I open it up on my laptop watch the tutorial then perform the procedure on my desk top. I am super happy with what I have taught my self but have been...

Yes I do believe it is

I understand about the carcinogen's... but I would bet most water tables are still better then the guys using nothing at all... I will keep you guys informed on how my table is doing.. so far almost...

Its funny My wife has it under the kitchen sink and the laundry room cabinet.. It helps keep the moisture down in areas so mold/mildew are controlled.

Sweet Thank you.. I will start a little more reading....

I have the reciepe for the DIY.. THe original company is out of business. They were near my location when they were open. There is another company selling a plasma quench, I talked to them a week...

I was never intending automotive antifreeze. Just looking into another option, as for the RV stuff I picked up I have let it stand for 3 days with metal in it.. And the metal started rusting last...

Is anyone or has anyone used somthing other then plasma quench or the DIY PQ in there water table.. Say RV antifreeze, non flamable corrosive protection and EPA legal.. I mean if you can put it in...

I have the TD cutmaster 51... Other than the support from TD Sucks,, I figured out how to make it work with mach. I love the machine only reason I did not go to a newer bigger machine from...

I know you have read through my build, I wanted to build just like you... But after weighing all my options purchacing the CandCNC dragon cut was the best option.. I have no issues, I put it together...

The unit appears to be 100% extrusion.... I am sure there is some machining on it but it looks really smooth. The V is a cap on the extrusion. As for the rack it is not screwed on but double sided...

I purchaced mine at McMaster Carr here are the part numbers
ordered 2-6 foot pcs and will make them fit my use.
1 4409T513 2 Each Open Hinged Cable And Hose Carrier, 0.98"h X 1.50"w Interior...