Hello, I think, in this special case, it's better to contact Heidenhain.
If the "new" machine has a RS-434 V.24 it's may be easier to connect it a old printer and send the data direct from the...
Type: Posts; User: edm-dsc
Hello, I think, in this special case, it's better to contact Heidenhain.
If the "new" machine has a RS-434 V.24 it's may be easier to connect it a old printer and send the data direct from the...
Hello
1. WHAT have you written there?
Can you separate you program a bit more so we can see what parts are used for what.
Add commends and stuff.
2. First try to start with a HP before you...
To no.1
Nowadays there are many machines that are curved straightforward so that it works a lot easier.
A rotation shouldn’t matter so much.
And as long as you AND your colleagues write the...
O0001
#500=0(COUNT TO 0);
N10 If #500 GT 10 GOTO 2000(IF COUNTER MORE THAN 10 JUMP N2000);
(MILLING OR TURNING PROG)
M06T01;
G01X100.;
....
....
#500=#500+1;
That makes sense!
Waking up in the morning, not fully awake yet, and taking off all the machine covering.. and in the end the mill goes through the workers head because the hand was still a bit...
That's almost what i wrote!
Hello,
The thermal expansion is relative and it complies with the measurements, the storage and the outside conditions.
Just to be simple I guess you are going to use a motor spindle. There you...
I would assume the lubrication cycle is in the PMC parameters.
The PMC is usually created and maintained by the machine manufacturer.
That’s why it’s important what machine you are talking about...
RJ45 is a network. You should first contact your machine manufacturer and if he can’t help out I would ask Fanuc afterwards.
Hello,
Have you turned the machine on and off?
I guess it won’t help much because according to your description the machine can’t write the absolute position into the Pulscoder.
You have to set...
What do you want to do with it?
Turning, milling, 3D milling, wire cut EDM?
For wire cut EDM a i3 and i5 and a NVidia graphic is enough,
For 3D milling you have to get a Gamer Notebook for...
Hello,
a text is always nice - but is useless, if it's translated in the wrong way.
Therefore the controller should always give a number together with the error.
Greetings
I don’t need an offer. I have a CAM for all application with possibly most available post processors ( I am not working in the production area)
I think that a software doesn’t need to...
In my opinion most CAM systems are just too complicated and too expensive for most applications.
When I used to be a miller and did not have the chance to use a good CAM system, I was able to write...
Hello
Learn the ropes? It’s 20-25 years old!!!
It’s actually an easy machine. What is the problem?
Hello
It is sure possible.
You’ll probably need a spooler or whatsisname…
What kind of gateway do you have between machine and perforated tape?
Greetings
Hello
Could you tell us the labeling of the monitor? Maybe there is somebody who doesn’t know the type of the transformer but who would check it at his (her) Maho.
Greetings
Hello
You should now that Makino is building machines for quite a while now...
Machine?
Manufacturer?
Type description?
Controller?
Hello
You probably should calculate the maximal consumption of electricity.
(maximal power input declared by the manufacturer)
If you’d like to know it more exactly, install a measuring...
Hello
Since you can read the error message, I would say it’s not due to the service connection.
Maybe the mouse in the wheel is hungry?
Seriously, what exactly doesn’t the machine do?
...
Hello
What kind of regulator?
Type, labelling, manufacturer….
If you provide more information, somebody will probably be able to help you.
Greetings
Hello
Some keys have 2 symbols. You access the second symbol with the shift key. It’s an upward-pointing arrow.
After you press this key, “^” has to appear at the monitor and then you have to...
Hello
Your problem is described here
>>>http://www.automation.siemens.com/WW/forum...858&Language=en
But it’s not solved, unfortunately
I’m not familiar with this DC converter but check...
Hello
Could anybody tell me whether I need an SRam-card with or without attribute if I’d like to save data at a 16 type D?
Regards, Michael
I’m not. Unfortunately.
I only know all Charmilles, some Agies with Agie-vision, Fanuc and Mitsubishi…
But I know a person who has a Brother and is very unsatisfied with the machine and...
I have already started… is the horse or the elephant bigger? Do they both have the same size? I’m asking for more ideas…
I could give the programs to you…
Greetings
Michael
Hello
Actually you just need DXF and PEPS.
I’m interested in model dxf files for wire eroding, too. Those for laser cutting are not really adapted for exact machining with a wire eroding machine…
...
I’m searching for technologies and wire tables for Robofil 200.
Could anybody make a copy for me?
Regards, Michael
You can read this out from the .tec file…
Greetings Michael