Search:

289160
The 2 larger connect pins are for can bus. It is 300 vdc can high, can low, 5vdv, and ground. The smaller pin , the one in the middle with the small cover , according to manual, are for...

Its ok. I did nt get it the negative way. It is a realistic opinion. It is really being a pain to set these up. I will try some more, if no success I sell it and I will purchase some 1600 oz stepper...

I have seen some arduino can bus shield. And there is also a can bus converter, that converts whatever signal from usb or paralel port into canbus packages.
I think the main issue is for me to find...

Ok. Can you tell me something about these motors?

Enviado de meu SM-G530H usando Tapatalk

I have 3 danfoss servo drives . It is also 400Vdc. Any ideia how to control them.?

Enviado de meu SM-G530H usando Tapatalk

Hello and Greetings
Its really good to hear that you are from Germany and work on the design industry. I have strong plans to move over to Germany and it would be great if I could get some advices...

Hello Henrique. I am Fernando from Campinas SP. The jorney of building your own Cnc machine is a great and rewarding learning experience.
If you need any help, technical advice, parts and...

I am Fernando from Campinas. If you need any technical advice, or if you need parts and components I will be glad to help. Whatsapp 19 98715 1315.



Enviado de meu SM-G530H usando Tapatalk

What are these boards for? I have 3 dc servo drive from Danfoss (krones). I am looking for a way to connect the motors in my pc and run it with a g code software. They are canopen and talk iec61131-3...

I have 3 Danfoss Servo drives, and I am having trouble to find a way to connect these motors to my computer and run it in a 3 axis cnc. The motors have all the drives and encoders integrated, so I...

Hello.

I am building a CNC machine.

Most of the mechanical parts are done. I planed to build a Medium duty CNC router machine that is capable to cut through aluminum and similar hardness...

How strong is epoxy granite, and where do I find a good quality unexpansive source?

Enviado de meu SM-G530H usando Tapatalk

Beleza Marciano. Sou de Campinas. Qualquer coisa estamos ai. Bem vindo.

Enviado de meu SM-G530H usando Tapatalk

Check the feed rate for the material you are trying to cut. It's a little complex to explain. But tomorrow I will have more time and I will try to help. But you probably trying to cut to fast...

Stepper motors usually makes more noise when operating micro step.. Steppers operate at micro, half and full step.
If the motors are in good condition this is the only thing I can think of up to...

Thanks.. Is there any link to this board?

Enviado de meu SM-G530H usando Tapatalk

I have tried to get more information from Danfoss, but so far have nt got any answer.
All I have is a PDF that explains the system set up. It did help because was out of this document that I...

Look,... if you have at least, a basic knowledge of electronics and digital electronics: then I think, you may be able to use the encoders ,that happens to be used, to control home printers. At...

Well. I wonder if I happened to post this question in the wrong category of the forum.
Either I am not welcome here, or the forum is dead. I have managed to have 2 answers to my post, and I...

284012

Enviado de meu SM-G530H usando Tapatalk

I just saw the video.. Yes the VLC system is designed for the food and beverage industries. But the motion system are drive integrated, but it still a dc servo-motor with encoder box on the end of...

Thanks for the answer and for the help.

But help me to understand... Is it even viable (technically and financially ) to apply these motors in a 3 independent Interpolatimg axis ?
I am going...

Hello.

I have 3 servo motors. Danfoss ISD 410. Thet seem to be very robust and high torque and precision thus I want to use it in my milling Cnc machine project.
But the obstacles I am facing...

Hello I would like to know what kind of signal controls a servo-drive motor. It has the drives integrated in the housing. The drives receives can bus protocols and on the documentation of the motor...

Beleza cara. Sou de campinas . Precisar de algo estamos ai.

Hey what's up. I am from Campinas. If you need anything, please let me know..



Enviado de meu SM-G530H usando Tapatalk

Be welcome Dan.
I have recently registered to this forum to share skills and knowledge.
I am on my way developing and constricting an all aluminum, servo-drive motor powered, I hope it to be a...

Hello.

I was lucky to find 3 motors like the ones in the picture among rubish material in a junk yard. They work fineand was removed from what was left of a lipstick factory machine.

I believe...

Hello thanks for this space to post questions and to answer others question. I will inevitably need advice and information about CNC aplications, but I would like to be also helpfull and share the...