Search:

yes algirdas, there is encoder built in motor. and i agree there are more common issues for taiwan made okumas - but turret goes unclamped happened 4th time for me now. never at old ones.
turret...

cncteac - thank You !! :)

cncteac - what do You mean by "lock parameters" ??
i checked the parameters already - looks ok. next option i thought about is to reload the software. but it will not explain why the problem happens...

Algirdas - we have "a few" okuma's already. and know how to handle with safety interlock. there is something wrong/missing/damaged or so. electrical drawings by local okuma representative costs half...

sabotage- thats my option ;)
parameters are correct, there is no dirt nor coolant under the covers, cutting accuracy is fine. no timing belt - turret is driven by a motor with encoder on it....

Hello again,

we have an Okuma LCC15 with osp 700L with no documentation at all. it just came from other plant and we have a problem right after power on - we can open the doors (auto.doors) with...

Hello All,

We have an Okuma ES-L8 IIM with control osp-U10L. previous model was called soarer. machine is 3 y.o. and pretty not much used.
problem 1. - happens it goes cutting with the turret...

Hello Mike_Kilroy
Hello Al_The_Man
Hello "Collegues"

complete data from optcoder:
Optcoder; type: IP160512R (or IP160S12R - not sure); source: 24V 100mA; no:9004 - 1229 60C/R , and "not hit...

its possible, ill try today

yes, input is 0v and 24 v dc.
and yes - sumtak - means heidenhain - says "this is oem equipment so we do not have any docs for you". i will give it to someone more clever with electronic than me to...

Al The Man - unfortunately there is no electrical drawing for this machine.
i took out the encoder from the machine. put a power source 24 Vdc to it and rotate the gear. when i measure the outputs -...

yes, and thats the question.
if i turn the encoder by hand - i can see it in dgn screen. but is this enough ?
if i put turret rotation from mdi - it rotates continuously or clamps somewhere in...

Hello !
I have a lathe with turret problem - it hunts during turret rotation and does not clamp in correct position. machine is hwacheon eco n2. control fanuc 0-T. turret encoder Sumtak optcoder...

youd better tell him how to deal with the problem not only "smart" advices

there should be a switch inside the control cabinet signed "install mode" - switch or lever. switch it, close to it there is a button signed "reset" - push it. take care to have nothing inside floppy...

Hello Guys,

sorry to say but its not the same Okuma anymore. first i thoght that taiwan made series (like soarer, now its called genos) have problems based on assembly quality - hydraulic pipes...

i have both - regular parameter and "pmc" parameters. our machine is excel 510 with fanuc 0-mc. magazine is pneumatic type - no tool arm. check Your email karan. and remember to exchange batteries ;)

hello underthetire :)
it did not got wet, but is was outdoor for 2 weeks in november - under the roof only. it sit for about 4 weeks.
i wonder the problem comes
1. cause of the transport,
2....

hello,
appreciating underthetires's advice - i think its not the software problem - not yet. you can switch install mode, reset the machine and see what happens. if it fails same way again - you...

Hello Guys, nice You solved the problem. i have similar one ;)
after M19 spindle load meter is growing till 70 - 90 % (was growing). spindle does not vibrate too much. just to make tool change is...

hello,

i have same problem with Fanuc 0-MC. memory parity error - we've exchanged the batteries, put in 900 parameters, rest of the parameters are also in. but we cannot input the PMC parameters...

hello ben_heinman.
the post is from a long time ago but i have same problem - and with fanuc 0M i do not have parameter no 3202... You have any ideas more ? thanks.

yes - we've had it dismounted to each single separate part.
also if we disconnected the motor from the pulley - took the belt out - the motor itself has the vibrations also...

hello guys,

i have similar problem with lynx220 machine.
during the turret rotation we have an alarm on the screen and alarm on the vision unit. vision unit is DVSD-TT-14A and an alarm on it is ...

hello,
i would not post new thread - so - we have same problem: alarm 322 cmos vacant area error.
i've googled already a bit - a solution to thsi should be to set 1 to parameter 6066.d2 to reset...

havent check. but looks like we do not have the brake clamped - or not completely. after turret positioning and after clamp - when turret stands still in position - motor shaft have a very small...

Mechanical side looks ok. i can dismount the turret to pieces and put back together - testing for a few hours (rotating the stations, rotary tools with different speeds and directions) and no...

Hello,

I have a multiplex 6200 with live tool and a problem with an alarm: 24 overload (2, 0, &0058)
Alarm comes from the turret i guess cause we still have some problems with it - turret...

i do not have VTBOR in programming manual for this controller - but anyway i will try.. Thank You.

OkumaWiz - Thanks for the tip. unfortunately its still not working nice. a temporarily solution is to rotate turret with the step of max 3 tool stations. if its does not reach so much speed the...