Search:

Hello
then don't use it and drive out with the feed...

Kind regards

Hello I think that is going to be difficult biggrin.gif
I think you will have to request one...
I think I still have an Excel list with some prices but I am not sure if it contains information...

And what software are you looking for exactly? biggrin.gif
Greetings

Hello
I guess only on one. As the previous writer has already said: the software has a lot to offer.

Kind regards

I only have to enter to about 0,8mm... I can’t use a side milling cutter as there are still contactors that overlap the case so that I can’t mill to “zero”! Then it’s only a contour with inner and...

Ahh Hello? I did not want to hear that! biggrin.gif biggrin.gif biggrin.gif

es exactly!

The top is welded together with the case per laser. I only want to mill the welded joint and the open the rest as a kind of can.

Would you deliver in1*D or somewhere else in the hundredths area?
My problem is that if the miller rips and damages the cases, then maybe a defect might occur in the lower 6 digits area..

So...

And sorry I forgot to mention that I can only offer air from the outside! biggrin.gif

Hello Alex
It depends on what you are planning to do. If you still want to mil then you should prefer a mechanical one. And it’s important how you get air to the spindle. Have you got air in the...

Hello CNC guys
Who has experience in the try milling process with micro millers until 0,5mn?

I have to mill a case who’s top cover has been welded. As the electronic is on the “inside”, I HAVE...

Hello
I have the following problem:
I always get files from Hypermill send to me that I have to mill.
I get the files as IGES or STEP and I often have errors ( at least that’s what Solidwork says...

Hello
That’s because of security issues. During the processing you can’t change anything. That doesn’t work with the Offset values G54 and so on either.
I don’t know if there is a possibility to...

Hello everybody,
I am looking for a BAZ with the following criteria:
3 axis
Traverse path in X min 1000
Traverse path Y min 1000
IKZ
Tool changer
chip conveyor
Heidenhain control system.
I...

Hello
Of course that’s obvious.
However, I would I would use it in the lower diameter area. And then only for finishing.
Regards

Hello
I am considering buying a Quick motion spindle from Big Daishowa. I would get the one that has

The revolutions multiplied around the turning point of the machine.
Or should I rather get...

Hello Speedy1
Have you tried to get something from HSMWorks itself?
Otherwise you could call my reseller HSMTec. Maybe he has something for you.
Best regards

Holzschneller Christian

Hello,
The big area as side machining, the 2 deep areas roughened
and finished with a end mill (open pockets)

Then you rough the slope with the torus and finish it afterwards.
Click onto the...

Hello,
I thought the same.
I found on the website also some that are electrical. BUT for that you have to get an Info post.

You are completely right; the cables in the machine are poor. ...

Hhhmmmm


Apart from that have a look at Big Daishowa. They also have something like that and it’s a Japanese firm and they always have good quality.

Hello
No, did not centre anything- just drilled and threads are done.
I countersink the threads after the cutting.

Kind regards

Well, I have drilled 21 meters so far and the coating doesn’t even have a scratch.

Overall a clean ‘issue’ biggrin.gif # m8.gif

Kind regards


Holzschneller

Oh sorry
ST37 steel, nothing special

Hello
I have tried out the drill from WNT and i am satisfied.
Rotation speed 6800 rev/min – diameter 9,4
Feed 1700mm/min
Thread forming with VC 50m/min


Kind regards

Holzschneller...

Hello nasdaq,

I cannot inform you about the software, but normally PPs always have to be adapted.
Regular codes for G-and M-Codes do exist, which are the same BUT also machine specific codes -...

;-)

;-)

Hello

I attended this course, too. I can make some things but it would be great to have a reference book.

Kind regards

Christian

Who could recommend me any books for Solid Works 2010?
Mostly component groups / machines or forming. I’d like to become faster/better in CAD.

Kind regards

Christian