Search:

The Machine is from 1993. So I think, the machine has not an encoderbelt. For the parameters you must have some informations about your options, so a technican can use a parameterchecker program....

Remove the Tool Release Piston from the machine. Now you can remove the Bolt from the aluminium base. Have a look to the left hand screw on the bottom side and check the other snap rings.
The...

It's my personally experience that we have more problems with the toolchanger mechanics on the SMM as by the MM if they have the same toolchanges (upper 200 000),but only with the Shuttles. Because...

You can't make a copy from the Mill Software on a Haas Machine. Only you can make a Backup from the Parameters,Settings,Programms,Macros.....
If your Main Board is bad, the software must installed...

DON'T do so!

It's right thats maybe the drawbar is for TSC, but you need some other parts there are NOT installed. The Tool Release Piston must be configurat for the TSC option and you need a...

The SMM has more RPM, More rapids, a faster Toolchanger, but the Normal MM has more max torque. You need speed to safe time, the SMM is faster, but if you only make 10 parts from the same, you don't...

What do you mean with the operating system? the Mill Software or the Datas(Parameters,Programs etc.)

You need your software revision, because it's different to make a backup between the older and...

It's possible but not simple. You must change/add some parts. The spindle is the same as the spindle with TSC, but you must change the Draw Bar. For activate the TSC in the control you don't need a...

push the Setting/graph button,write 53, put the arrow down and than the arrow right. Now you have the setting 53 (jog without zero home) highlightet. confirm them with the write enter button and go...

Hello,
have you got more informations? Is the barfeeder running before or it's a new installation? Can you jog the barfeeder with the wheel in the handlejog?(V-axis).
Maybe it's only a problem...

Your finances are limited? Buy the Mini Mill.

You looking to add the 4th and 5th axis? Buy the Mini Mill.

Yes, there is a kit for the parts catcher option. I don't know the correctly price in US $ but is nearly 2000€. on a SL-10 You can install the option by yourself or you can call and pay a Tech for...

The 12K Motors are listed for VM and VF because there are for the VF-SS Inlinedrive. It's not easy to see only in the sparepartlist. I'm sorry, I miss my brain.

I've only look on the partnumbers from the motor in the sparepartlist.
In the list is the lincoln 12K Motor for the VM and for the VF, and the Baldor 12K Motor for the VM and for the VF listed. ...

If you look from the front of the machine, it must be the upper connector on the right side from the plate.

But it's not dangerous to test, wich one it's the right. Put the fan in and start the...

Yes, your right, but the question was only about the Motor, not for the spindle.

I think they have a 12K 20HP Motor for the VM Moldmaker machines and the same motor on the VF series without Gearbox and the 10K option. On the VF- the Motor only run 10K about the parameters. But...

The OL-1 has a X Travel 12" against the 6" from the SL-10. the OL-1 is smaller and the machine weight is only 1300lb. You can put the machine in the second floor in an small room.
for some guys the...

Hello,

at the first: Sorry for my english.

I will try to explain it.
Your machine has a pin for the spindleorientation. this pin push in a hole from a ring. If anything from this parts...

Hello,
you need the Haas number from the Main Processor board for more informations. There are different boards in the machines.
look on the inside of the cabinet door. Maybe you see a paper with...

Have a look at the setting 130. Change it to 1 and try it again.

Maybe the bulb is loosened? Check the Plug connectors on the adaptorcable and on the i/o PCB.