[QUOTE=mazak-user;2067636]Hi, give me your mail, I will send you some data sheet.
hello,
I wondering the same thing, please send also to my email address.
[email protected]
I want to...
Type: Posts; User: nastek
[QUOTE=mazak-user;2067636]Hi, give me your mail, I will send you some data sheet.
hello,
I wondering the same thing, please send also to my email address.
[email protected]
I want to...
Hi..
I just bought a stepper motor from junk shop
Sigmax (Pacific Scientific)
Model: 802D3450-F05LF
Please help from anyone for datasheet.
thank you
Nastek
Dear Hadi,
Your setting isn't complete yet, probably comes from RS232 cable and parameter from the PC.
Mitsubishi use 7-2-4800, parity : even
if any question please send PM..
Hi....
I bought 2 pcs used step-syn stepper, but I do not find the datasheet.
I ask if anyone knows the specs of step-syn stepper.
Stepper type :
1. 103-8573-5040 (10 wire 5 phase)
DC...
hybrid ic is DK..., ussualy for driving mosfet transistor, there are 6 pcs.
hybrid IC is damaged, check its type, maybe I can help you
please connect VRO to 24V, and make sure VRO Rellay is on ( find it on controller door cabinet ), or give a jumper VR-IG on Rellay terminal.
can we talk on YM?
Can you contact me on blackberry messenger or yahoo messenger?
operation parameter :
CNOd :0
FNOd :1
ACC : 0.4 (if you get alarm on start, please increase value)
DEC : 0.6 (if you get alarm on stop, please increase value)
FH :120
UL : set to max rpm that...
Hi ben,
you need to set inverter's parameter
Eg. Input command, max. Freq, etc
1. You lost the parameters
2. Please change FA (alarm) to FLB on inverter, wrong pin connection
Try to reinput parameters
okay, ready for test
Do not use CON 2/3. Use Con 1 pin 11-12 for Alarm Detector.
FRSX (ARST1+ARST2) Connect to Toshiba (CC+RES) for reset the alarm.
please read the first page of this thread.
hahaha, very interesting.
for the resistor, you can use 10 ohm/660 watt.
or you can use the existing resistor if it present.
Ps. thanks for the offer, I'll be delighted
i see on your website, you make tray for battery, i think my car need it. hehehe
Up to you, but some processing part need fast stop.
or you can try to use original Braking resistor ( if the resistance above 12 ohm ).
Braking resistor only use for stop the motor by DC...
don't forget, you must buy braking resistor to get fast stop.
Hi benjamin,
Sorry for late reply,
VFS11-2110PM-WN 240V/3 is good enough.
Thank you,
I've seen the wiring diagram, the ERS is NO. that is connected with the relay.
if the relay on, ERS = 1 and if the relay is off, should ERS = 0,
but at the machine in turn on, relay...
Control Goes "Ready", everything looks fine.
But the status is "RESET".
i can't move the axes
Diagnos ERS : 1
What causes the ERS: 1?
Thanks
Hi Nate, happy new year for you
Tired after vacation, but the best think if I can share my experience for the people around the world.
I never use the feedback, and if you can set the best...
Cncserveng, thanks for advice,
Btw, when the reset pushed, RST : 1, no change signal
The machine have no hydaulic
Any external input that make it happen?
Thanks
http://www.yaskawa.com/site/dmspindle.nsf/%28DocID%29/TKUR-5EKSVU/$File/NTR0010.pdf
Hi Nate,
Check this, http://www.yaskawa.com/site/dmspindle.nsf/%28DocID%29/TKUR-5EKSVU/$File/NTR0010.pdf
This Drive is similar with inverter, you can use it.
Btw, if you want quick ACC/DEC, you...
I had a problem in Fanuc 10 type A horizontal milling.
when the machine on, ready on, everything is good.
However, at the monitors perform reset, as when the reset button on the press.
I see...
I think you should use Toshiba, i don't know ABB performance, from the spec, ABB only has 31A Max. current.
You can't get faster ACC/DEC than toshiba, and you should buy keypad.
Mitsubishi freqrol...
Dear All,
I have a plan to retrofit my milling machine. These machines use Fanuc 10M controlller.
AC servo drives A16B-1200-0670, in good condition.
Masterboard Type A16B-1010-0190
and I want to...
Thank you sir, i will find the match driver for this motor
Dear Sirs,
I have a dc servo motor "Electro-craft" that will I use for Mach3 software.
I do not know the specs.
If anybody know the datasheet, please help me.
Thanks
Nastek