Hi.
Anyone have idea with this alarm Fanuc 0.(Dot) on Fanuc PBFM.
Replaced the module but problem is same.
Checked all wiring but everything good.
Any info on alarm or some one has manual for...
Type: Posts; User: jjautomation
Hi.
Anyone have idea with this alarm Fanuc 0.(Dot) on Fanuc PBFM.
Replaced the module but problem is same.
Checked all wiring but everything good.
Any info on alarm or some one has manual for...
Hi,
You need machine SRAM Backup then only you can reload the machine. This method is applicable for M600 only. M60 uses ALL1, ALL2,ALL3 files to reload
Hi,
Anyone has backup of Mazak VTC-16C.
Please PM or email me..
Thanks in advance
Hi,
There is only lock B. I have already tried that lock.
In manual also it is written that you can take system paramter backup but you can not load back to machine.
Sent from my SM-G950F using...
Thanks for the reply..
Option Parameters are available, I think so. When you press option settings key inside Maintenance menu. System asks for password. But there is a sceen to view installed...
Hello,
We are working on a Mitsubishi MV-5C VMC with Mitsuibsihi M600(FCA610MT) controller.
Machine was working okay 5-6 days ago.
3 days back machine battery became low and the...
It show the port setting in machine is wrong..
Change parameters as below
0002 10000011
0038 10100000
0552 11 Baudrate 9600
ISO is located 2 page up from parameter 0001
Change ISO to 1...
Check in custom PMC manual some address can not be used as a coil these are only for DI and DO for main PMC to Custom PMC..
Sent from my SM-G950F using Tapatalk
Is it a robodrill...
Sent from my SM-G950F using Tapatalk
Search in ladder that this coil should not have 2 coils in the ladder.
Sent from my SM-G950F using Tapatalk
Either the coil R2200.0 is used twice some where or there is a jump instruction prior to the coil somewhere above.
If jump JMP instruction is high all the coils inside the jump will not turn ON.
...
Hi,
I have a list of leadwell parameter. Share your email id.
Sent from my SM-G935F using Tapatalk
Hi, which manual do you want?
e.g. Maintenance, parameter etc.
Sent from my SM-G935F using Tapatalk
Thanks for reply.
That is what I am looking for, how to configure servo axis as a spindle.
Sent from my SM-G935F using Tapatalk
Hello Everyone!!!
I am working on a CNC Turnmill with Fanuc 0-TC.
Machine model is Tecno-V 45X3
Machine has 4-Axis, X and Z as normal turning center will have,main spindle with Bzi sensor and a...
Hi
Did you get any solution for the above problem.
I am also facing same problem. PS 099 pops up as soon as M6 is about to finsh.
Rgds
Harmeet Singh
Hi
Did you find any solution for the above probelm.
Please let me know as I am also facing simillar problem.
In my case PS090 pops up as soon as M6 is about to finish.
In my case there is no...
Last day we replaced the motor with another motor.
Replacing motor was not new one but refurbished one.
Machine is Takisawa TC-10 CNC lathe.
Motor is for Servo controlled Turret
After replacing...
Okay
Thanks for reply.
Motor winding is okay, insulation resistance is fine.
Motor encoder reading is okay, motor is rotating smoothly outside the machine but with low torque.
Sent from my...
Hi everyone.
I am working on a Beta 2/3000 motor. When we power ON the control as soon as motor comes in servo lock, if we try to rotate the motor shaft it rotates with a very little force and in...
Hello all,
We are facing a problem in a turning center with 0i-TC control.
When we switch On the machine, machine comes to LOADING GRAPHIC DATA screen but stops there with CRC ERROR! as in...
And check Keep Relays manually from okay machine to this machine. Write them on a paper.
Sent from my GT-I9100 using Tapatalk 2
Your method is correct....
But if you are loading PMC parameters, then keep relay data is included in it.
You should now check your machine ladder.
Just check your turret index push button input...
Hi Ahmed
You haven't told it is VMC or Turning Center.
If it is VMC there is TooL Data in PMC Parameters...
From where you took ladder backup, take PMC parameters backup from the same machine...
hi freemanxxx
No Idea...
I have also done research but didn't find anything...
From my idea these files are written in separate program and then compiled as Fanuc ROM file..
ex: Custom macro...
If motor is getting heat up, check load on axis. Excess load on axis causes this alarm.
Sent from my GT-I9100 using Tapatalk 2
Soft thermal alarm comes from digital servo. There is one parameter in the machine of soft OVC limit. I dont remember parameter no. Check parameter manual of machine control. Check if motor in actual...
You didn't mention how alarm occurs, while running or just turning ON the machine?
Sent from my GT-I9100 using Tapatalk 2
As I already told you, alpha drive doesn't have parameters in the drive. You can replace the drive of same spec anytike, without any need to change parameters.
Sent from my GT-I9100 using Tapatalk...
Than the problem should be in main board.
The axis card/module is making the problem.
Sent from my GT-I9100 using Tapatalk 2