I'm exploring this. Trying to mate nikken 5AX to a aT10A robodrill. There is a video of one on a 16C, so I am figuring it can be done. On the motors and drives/encoders I have that covered (6066 amps...
Type: Posts; User: regina
I'm exploring this. Trying to mate nikken 5AX to a aT10A robodrill. There is a video of one on a 16C, so I am figuring it can be done. On the motors and drives/encoders I have that covered (6066 amps...
Try these guys: https://www.ebay.com/itm/VGA-LCD-Controller-Board-Monitor-DIY-Kit-For-LTN154X3-L01-CCFL-30Pin-US-Seller/162708327950
and tell them what panel you have and what your signal specs...
On this note, does it do it if the motor is electrically connected but not mechanically coupled? (bad bearing or screw or something, clamped axis?)
Book says language is either
PMC–SA1
PMC–SA3
for the 21B
I dont think there is a module for that in FAPT
I think you need ladder II or ladder III.
I'm trying to add a 4+5 th axis nikken truncation table. This control is using (x3) 6066-h004 c series amplifiers, and has serial A encoders on the X,Y,Z. I have the additional amps, a06b-6066-h003...
I have delta three phase available and want to connect and use this old EDM. One leg is high though and I am wondering if 1 of the three terminals would be better for the high leg and which one. It...
Yes this is likely a multi axis servo drive. Any one failure can bring the whole drive down. I'm learning to hate these. It may not be anywhere as bad as you think though. Could be a breaker or...
Hmm didn't realize the 14 meant a 14 tool turret. Sorry about that.
If you have that program that has a header written for your machine I would definitely go with that instead and parameter wise- I...
The less elegant method is to remove the turret cover and pry against the gear and just put the turret where the machine thinks it is and just run with that. You have to overcome the strength of the...
My manual says it is the value in parameter 7825 divided by 10
In my circumstance it worked out to be 95.5, your mileage may vary.
I had to research that my myself, even methods coundn't tell me...
This is the reference program for mine an alpha t10. It's probably the same for you. I had to go through the same thing
N0060 ?.?? is specific to your machine and it is derived from certain...
In the morning try giving these guys a call. They are familiar with that machine and will have better info than what I can give you.
Post back with your results.
...
I don't have any 6m experience yet. I have a machine with one, but I probably won't have it up and running for a few more weeks. I do have most of the manuals in hard copy. I'm just searching the...
Searching the forum yielded "
LSK means "Label Skip", and you really can't get rid of the display (unless you want to reprogram the CNCs EPROMs)
Fanuc refers to the the "Label" as any...
Memory data is gone for sure. Hard to say if you messed up anything else. How does the display look if you have the batteries out completely? If it is Also, Is this a A. B, C. or D? Not sure if that...
I am trying to transplant the color mdi/CRT/softkeys and graphics card from one machine that is being scrapped to another one that I intend to use that just has the basic small monochrome mdi/crt...
I think you may have reset the turret, but the head is up too high in Z and is in the area normally reserved for tool change. This can happen when interrupt a tool change in progress. I pulled my...
Got it home safely today. Manual lists at 12,125 lbs but I think that is without the control. I would estimate it was about 14,500 for anyone's future reference.
Anyone? I have to go and pick it up tomorrow.
Yes it must be timed to the motor. This has been addressed here before. The instructions are in this post:
https://www.cnczone.com/forums/fanuc/258532-procedure-installing-fanuc-pulse-coder.html
Thanks, that at least gives me an idea how it works. I wonder why they made so may variations instead of just having every one populate the full matrix. So much skipping around. Where in the...
I was wondering what it takes to use the newer style MDI ( https://www.dnc-electronics.co.uk/parts/fanuc-monitor/crt-mdi/a02b-0162-c092/ ) with the 15A. The older one with the membrane keysheet looks...
Hello all I just bought an old millac 4va and need to figure out how heavy it is to ship it home I've seen weights listed from 12500lbs to 17000lbs what's the real deal?
Thank you drdos! I was able to successfully format the disk and back up my file :)
Someone else also shared some other commands with me and I thought I should share them here in case someone else...
Does anyone happen to know the command to format a blank disk from the "request" line? "format" doesn't work.
It won't let me save to a plain blank disk. I assume I have to format it first.
...
In a semi related topic I have some nice PCI and ISA Galil motion control cards, cables and breakout boards along with the industrial motherboards to run them with mach I bought when I thought about...
From what I'm learning none of the retrofit stuff is "easy" unless you buy something like a centroid that is pre configured to your application. You are going to have to find out more information...
I got the idocs mailed to me, but there are very few manuals for the 15A in it :(
I bought the GFZ-61222E 15 MA descriptions off ebay but it looks like I will still need other manuals to find out...
Not to sound dumb, but did you look for a mag sensor/s to see if it/they have chips or anything on it? Are you cleaning with compressed air? That would be a likely culprit. Or else test it some how?...
Following with interest. I have one of these drives I will need to use in the intimidate future. What manual and schematic are you guys using to troubleshoot?