Search:

https://www.youtube.com/watch?v=kmItSasTZ1s
How can I RichAuto A18 dsp the programmer with Code Composer Studio (CCS) a programmer?
Training is in the film, but I do not understand.
Can anyone...

Dear Mr. i use this Driver six months for my cnc. Until now not encounter the problem. Please tell me what the future this problem will have consequences thanks.

HI

LS7290 STEPPER MOTOR CONTROLLER

80V 7A Drive

LS7290 Controls Bipolar and Unipolar Motors

Full, 1/2, 1/4, 1/8, 1/16, 1/32,

hi
The THB6064H is a PWM chopper-type sinusoidal micro-step bipolar stepping motor driver IC.
It supports 8 kind of excitation modes and forward/reverse mode and is capable of low-vibration,...

hi
PWM Chopper-Type bipolar
Stepping Motor Driver IC
Schematic and pcb TB6560A whit protel dxp.

Features
• Single-chip bipolar sinusoidal micro-step stepping motor
driver
• Uses high...

Here is a Schematic of A3986 whit protel dxp.

hi.
can anyone tell me which one of converter I must use for convert the .txt format of protel 99 se to .Gcode format.I am going to use of mach3 interfacing for my cnc machine.
Thanks.

Hello
Check out here .
http://www.modularcircuits.com/h-bridge.htm
http://cnczone.com/forums/showthread.php?p=341568#post341568

I find in to web ( http://avr.cnta.net/PcbDrill2CNC/PcbDrill2CNC.html) this china softwer for conversion a pcb protel drilling file (txt) to g code (tap) for mach2/3 cnc. do any have similar softwer...

Happy Holidays.

How to change BMP or JPEG to Dot Matrix bmp file for make a painting with cnc (which softwer).

thanks.

hi

I have that image and i want a g-code file. Do you have any pics of that or Similar?
thanks.

hello
thanks for answer.
Regards

hello
i am buying 3 ac servo mottors. can i used ac servo for mach2 ?
Regards.

Hello
you can used of this pcb (protel 2007).

have good time.

Hello All .
Has anyone used the .txt or .drl files generated by protel to drive whit MACH2?
someone help me with some hints on how to convert the protel .txt or .drl files to a useable file type ?...

Hello.
Dear professor.
This is Mardus-Kreutz project stepper pcb RV1.
I testing whit 4amp stepper motor. it is good.
thanks for you help to design this pcb.
Regards ,
Reza.

HI
you can find more information about this matter.

http://www.robotyka.com.pl/forum/viewtopic.php?p=120&highlight=
Regards
nasr1

HI
that one sample of circuit.
i building completely with protel softwer.if you can working with protel softwer i attached for you.
regards
nasr1.

HI
Thanks for the info.
I finded in to web .
i have no information.
i have necessaries trunery for this subject.i am to
make ready.but i need information about electronic controller.
i am...

HI
You can use this driver for 6AMP stepper motor.

HI

how to control this robot.

if you have any suggestiong it would greatly appreciated.

thanks.
nasr1

HI
here is a clip OF stepper driver with L297+7409+IRF520.
I hope to take pleasure.
nasr1

HI
I working whet protel 2.7 pcb.

Regards.

Hello all .
I have files of elm smc&smc3a & power mosfet protel pcb and pdf .
Regards,
nasr1

Thanks.

Thank you for response.

how to connected this circuit with stepper controller.?

Do you have a schmatic of stepper controller with an encoder.?

Hi all
I need to be able to contol a motor simply by turning an encoder shaft and have the motor respond in position, velocity, and direction accordingly.I need a schmatic of stepper controller with...

HI kreutz

Thankful.

I could not find ic UCC27424D do you have similar of this ic.?
Regards,
NASR1

I am looking for a relative low cost Drilling pcb software (DOS). that works whit stepper motors. if you have any suggestiong it would greatly appreciated..

thank you,
nasr

hello
thanks for your answer.
I am try to test it.
Best regards.