Search:

I am trying to repost my post pictures, below I'm confused a bit but I noted two icons in the upper left hand side (cnczone) and (industry arena) my pic show in the latter but not here, it seems the...

Hello,

I am trying to see if the picture format is the problem, else any suggestions? Let me know if this one works?

Thanks

488655

Thanks all for the advice, I am playing around some more and I'm making some progress

@joerlane

I do have limits set up for homing as in my pic, I do like homing and am used to it for my mill,...

Following up to my previous post, I did manage to get the toolpaths to show in 2D viewer, so its sort of making sense now, but when I try it on the real machine, I can't seem to get the start...

Hi I am trying to set up a Unimat lathe using GRBLGRU V5.0.0 Win 10, for some reason, I have no view now of anything in the 2D viewer editor? tool, toolpath etc.. It was working now it is not? please...

Thanks for the reply! I was able to disgnose the problem. Turns out, I had 2 case coolong fans which had wore out!! Appears these must have been shorting the PSU no power on either 12v or 5v ..I've...

I've had my mill converted and running for a long time. Last time it was used was this summer. I turned it on a couple of days ago and a funny thing happened? I'm running the CllG rev 8.2 with Gecko...

Hello,

I have scoured the net for some time now and did manage to find some info on this topic, but it seems the majority are geared to using auto tool setters. For some reason the probe thing is...

Air/Hydraulic, that's what I would like to see! :)

I have the limit switches on pin 12, 15, 13 and jumpers not set to pull up, I read 4v in mach I have them with the green check mark in the active low they work fine..

Jayc using the C11G vers 8.2 and have the pin 11 jumper set to pull up position...tks,

me again, ok so I tried the voltage test and there is 0V it is not pulling it up? any suggestions?

Thanks,

Hey Hoss nice work!...I have my stepper mounted in the back of the column it's a great place to have it out of the way, but a bit of a PIA the way it is set up..I have a mounting plate on the column...

I do have all my shielded cables only attached at one end at the control box, will do the short wire test and see what happens...hopefully this will finally work! thanks..

templecorran: my probe does the same sometimes, but usually it moves just slightly and stops? It doesn't touch the part but tells me alll axis are zeroed.. ger21: I have the probe set up using the...

hey Trell,

I can't seem to get this working right either, I do think I finally got the wiring correct, if I trip the probe by hand the light comes on, but when I try to probe (center probe for...

sorry Hoss here is a pic, did you need to add more threads to the top?

Hey Hoss,

Did you have to add more threads at the top of the spindle for the pinch collar?

Thanks

The Solenoids at Princess Auto are from EMC

pneumatic cylinder, pneumatic valve, pneumatic fitting, air cylinder, pneumatic components.

Princess Auto in Canada have these..but not sure if DC would be what you need?....just a thought...:cheers:
...

Hoss, do you have a picture of the what the new drawbar looks like out of the spindle? I am planning on using the smaller Bellevilles identical to what you have on your X2, do you think 10 back to...

Hey Hoss, Nice job! I like the way there is minimal load to worry about on the spindle bearings!...I am assuming you made a new drawbar altogether as the original is much shorter...is that collar at...

hey neilw20

Thanks, that makes me a bit more relaxed, what about the C11 BOB?

Hey All,

Hope someone can help confirm my wiring setup and a couple of questions...Here is my setup:

Cognitive inovations probe:
Cognitive Innovations: News

I have the C11G BOB with one...

Hi All,

Newbie, I had my machine running good.. it's a Busy Bee conversion CT129 built based on Ellik's kit.. but I have run into a problem the other day. It started when my Z axis fuse blew. So...

control box ready to be wired...

These guys got me hooked! I have had my CT129 for a couple of years now, it's the original version that was available when this mill was first sold by Busy Bee, the main difference an MT2 as opposed...