So I retrofitted this hurco a few year back and I no longer need it. I'm considering selling it but not sure what to ask. The servo motors are what came on the machine. I used viper drives to...
Type: Posts; User: freak_brain
So I retrofitted this hurco a few year back and I no longer need it. I'm considering selling it but not sure what to ask. The servo motors are what came on the machine. I used viper drives to...
early 09
By the way, I'll have a hard time sleeping now. That poor chevy motor!! :)
Jackal
Yes, I turn my spindle on with a M3 then adjust rmp as needed with the switch on the front of the machine. Using the dial on the front to set rpm. I think there is something still on the...
Jackal,
I am no wiring guru, thats for sure. I just kept looking and asking until I finally figured it all out.
As for the spindle motor. Simply put my machine is pretty job specific in what I...
I too have coverted a km3p using vipers and mach3. everything went pretty smooth with the exception of a couple of things.
1. The vipers at the time had a problem saving settings to bank 1. took...
Ok, it's my fault!! vipers have been working flawlessly until I crashed Z axis last night. Now the drive has a medium flashing red light along with the solid green and Z won't work. any suggestions?...
Hello Ronny
Nice job on the new machine. Keep up the good work!!
I was wondering if you have put life to her yet? I was thinking about using those same drives (leadshine), on my new project,...
Sean,
There are uses for that type of plasma cutter. My brother and make custom parts for race cars. Aluminum valve covers are one of our biggest products. I have often thought it would be nice to...
The 80/20 extrusions will cost you more than using a steel construction. However, if you don't have the equipment to fab it out of steel the extra cost is worth it.
Allen
Does the MB1 have a motor to adjust the speed up and down? I know my KM3P has a prox sensor on the spindle shaft with a small 3ph motor to adjust the rpm. Is yours the same?
I am finishing my...
I got it worked out today with Larry at Larken.... Very good guy to deal with!!! A1 service!!!!
Thanks
Hello All!
I am retro fitting an older hurco with viper 200's. Everything is working great on Y and Z but X won't move. I moved all the wiring from the X board to the Y board and it works like a...
Al_ The_Man,
Now that I went back an re-read my post I seen how it was not clear as to what the prox switches are for. Sorry about that.
The prox switches are the limit switches. All the wires...
Hello Everyone,
I am retrofitting a older hurco (KM3P) with viper200 drives. A lot of the "stuff" from the original machine I am keeping (servos, power supply transforers limit switches etc.)....
Hello everyone. I called Hurco the other day looking to get information, on the motors, on my KM3P. The tech guy sent me a pdf file and I thought some others may get some useful information from...
Hello Again
I put that file on my bro's website. Buy a set of valve covers while your there :)
Here's a link http://www.jgangracing.com/KM3-3P%2520Drawings[1].pdf
Hello Folks!!!
I found some stuff on ebay that someone may want for an older hurco? Personality boards, drive boards ect.. Anyhow, here is a link...
http://shop.ebay.com/merchant/paj1206
...
I have a pdf file that Hurco sent me on the KM3P's. Has a lot of wiring information. It's to large to attach in on cnczone. Email me at [email protected] and I will send it to you
Allen
123CNC,
I have AOL (or maybe it way yahoo) to thank for the name freak_brain, not my higher education. Only an idiot would have the user name freak_brain, right??? :) It was one of those things...
DonnieET, 123CNC,
Thank you both for all your help!! You two rock!!!
I do have servomate (CMC) and I think you are correct about the servos. The numbering in the new catalogue is different but...
Donnie,
Thanks for your reply!!!
I am rather new at making or rebuilding CNC's but I have made 1 before with geckos and Mach3. I am not familuar with EMC2 at all!! If you have time can you...
Hello again
After looking through some of my documentation I found the following part number for the servos. It states that it is a EC servo part number 401-4003-015. Maybe this will help.
...
Hello again
After looking through some of my documentation I found the following part number for the servos. It states that it is a EC servo part number 401-4003-015. Maybe this will help.
...
Hello All
I am going to retrofit my KM3P so I need to figure out if the viper200 drive will work with my servos. If not, what will? All the tags on the motors are not readable. I did get a model...
Hello All!!!
I recently purchased a hurco KM3P. After some issues I have had (and others I have read about) I have decided to retrofit this machine. One of the many open issues is my servo motors....
That worked.... Thank You
Larry
I have visted your website for the past couple of days trying to download your manual on your viper 200 servo drive. For some reason it don't show up!! Can you post in on here for me?
...
I think as a general rule static phase converters are not recommended for CNC machines. However, it sounds like all you are looking to do is power the spindle motor with the phase converter. I would...
Buddy,
I got it!! All I had to do is change the "file type" from NC to HNC. The file extension was always HNC but the file type was NC. I changed it over and bam!!
Thanks to both of you for all...